Jump to content
We Need Your Help! ×

Welcome Guest! Please read more information about our club!
  • entry
    1
  • comments
    2
  • views
    1,333

Brake Lights only come on when hazards are on.

mikeddiezel

Entry posted by mikeddiezel

719 views

 Share

New to me 72 240z. Replaced all the tail light bulbs and replaced brake light switch. The older brake light switch had different connectors than the new correct one. Old brake light switch had one yellow wire from under the dash and one of two green wires connected to it. Headlights, running lights and reverse lights all work. Turn signals do not work and have not since car was purchase a few months ago. Here is what I have going on as far as I can tell. When I connect both green wires to the new brake light switch the parking lights come on and stay on with me stepping on the brake. One of the connecters gets really hot. When I connect either one of the green wires and the yellow wire that comes from under the dash (looks like the hazard switch) to the new rake light switch the brake light only come on when the hazard switch is turned on. The turn signals also only work when the hazards are on.

I have searched a lot of threads but I have not found the help I need. Any help from all the collective great minds would be great. Thanks in advance.

 Share

2 Comments

Recommended Comments

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Blog Statistics

    • Total Blogs
      167
    • Total Entries
      251

  • Blog Comments

    • Jeff G 78
      280z Disc brake conversion

      By Jeff G 78 · Posted

      I'm still waiting on a hoist to free up before I can start bolting the new brake parts on my Z, but I did make the drill jig today.  I started with a 12mm thick Mustang wheel spacer with a pilot.  I then made a drawing to layout the holes needed.  I transfered the drawing onto the spacer and I drilled three new 1/8" holes through the jig (spacer) so I'd have the correct 4x114.3mm holes.  One hole is shared from the original 5 lug rotor.  I then bolted the jig onto the Mustang rotor and simply dr
    • One Way
      Looking for a 1978 280z Gas Tank

      By One Way · Posted

      Local radiator repair shops used to be plentiful but getting harder to find.  Some of them just specialize in big truck-heavy equipment radiators.  I will be needing to do the same for my project.  I have heard good reports on gas tank RENU but there are none of those franchises in my area.  Good luck, John-Lugoff, SC
    • Yarb
      280z Disc brake conversion

      By Yarb · Posted

      Decided to go with the 240sx conversion. Main reason is it’s strictly for the street and the parts were easy to source. What I didn’t realize was the 14” wheels won’t clear the caliper. Now looking for a set of 4 lug 15” rims and tires I can use during the build process. Can anyone recommend a temporary solution as far as make and model preferably a steel wheel that I can use until I’m ready to buy the wheel and tire combination at the end of the project? Thanks again for all the help out there.
    • Jeff G 78
      280z Disc brake conversion

      By Jeff G 78 · Posted

      There are several reasons to use the S197 rear brakes.  The rotors are larger diameter than the SVO rotors and they are vented.  The calipers have larger pistons to give them more power.  The big beef with the Maxima rears is that they don't offer as much stopping power as the stock drums.  The S197 rears allow the addition of an adjustable proportioning valve.  The Maxima rears cannot utilize an adjustable prop since the prop needs to be all the way open to get close to enough rear bias. 
    • the_tool_man
      280z Disc brake conversion

      By the_tool_man · Posted

      Any particular reason to use S197 Mustang 5-lug brakes?  The Fox body SVO Mustangs had rear discs with 4-lug.  It's a popular swap to use SVO or T-bird Turbo Coupe rear brakes to retrofit discs to other Fox body Mustangs.  These parts are still pretty common (probably available as a kit).  Might be worth checking to see if they'll fit.
×
×
  • Create New...

Important Information

By using this site, you agree to our Privacy Policy and Guidelines. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.