Jump to content
We Need Your Help! ×

Welcome Guest! Please read more information about our club!
  • entry
    1
  • comment
    1
  • views
    1,513

my car wont start getting gas but no fire anywhere

william12

Entry posted by william12

617 views

 Share

everything is new...i just had the motor rebuilt and the guy was suppose to put all new parts ( battery,starter,coil,ect ) on it.when i picked it up it started fine then i had it hauled to a guy to fix the body and paint it.he was taking forever and working on other cars in the same building as my car and it wasnt covered up and had all the sanding and everything else all over it and all over my motor he said he lost my key so we pushed it out and i had it taken to my house.now it wont start there is no fire anywhere.my brother had a friend over here last week but i was gone but he said the guy went to the battery and hooked something up and it started and said it was the fuse box.i replaced the fuse box but still no fire...wont start i have spent almost all my money on this car...i dont know where to start now or how

 Share

1 Comment

Recommended Comments

James Bell

William,

If you have points in the distributor, check the point gap. Also, my Z would not run due to a bad condensor located on the distributor. Replacing this and the engine fired rught up.

Jim

Link to comment

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Blog Statistics

    • Total Blogs
      167
    • Total Entries
      251

  • Blog Comments

    • Jeff G 78
      280z Disc brake conversion

      By Jeff G 78 · Posted

      I'm still waiting on a hoist to free up before I can start bolting the new brake parts on my Z, but I did make the drill jig today.  I started with a 12mm thick Mustang wheel spacer with a pilot.  I then made a drawing to layout the holes needed.  I transfered the drawing onto the spacer and I drilled three new 1/8" holes through the jig (spacer) so I'd have the correct 4x114.3mm holes.  One hole is shared from the original 5 lug rotor.  I then bolted the jig onto the Mustang rotor and simply dr
    • One Way
      Looking for a 1978 280z Gas Tank

      By One Way · Posted

      Local radiator repair shops used to be plentiful but getting harder to find.  Some of them just specialize in big truck-heavy equipment radiators.  I will be needing to do the same for my project.  I have heard good reports on gas tank RENU but there are none of those franchises in my area.  Good luck, John-Lugoff, SC
    • Yarb
      280z Disc brake conversion

      By Yarb · Posted

      Decided to go with the 240sx conversion. Main reason is it’s strictly for the street and the parts were easy to source. What I didn’t realize was the 14” wheels won’t clear the caliper. Now looking for a set of 4 lug 15” rims and tires I can use during the build process. Can anyone recommend a temporary solution as far as make and model preferably a steel wheel that I can use until I’m ready to buy the wheel and tire combination at the end of the project? Thanks again for all the help out there.
    • Jeff G 78
      280z Disc brake conversion

      By Jeff G 78 · Posted

      There are several reasons to use the S197 rear brakes.  The rotors are larger diameter than the SVO rotors and they are vented.  The calipers have larger pistons to give them more power.  The big beef with the Maxima rears is that they don't offer as much stopping power as the stock drums.  The S197 rears allow the addition of an adjustable proportioning valve.  The Maxima rears cannot utilize an adjustable prop since the prop needs to be all the way open to get close to enough rear bias. 
    • the_tool_man
      280z Disc brake conversion

      By the_tool_man · Posted

      Any particular reason to use S197 Mustang 5-lug brakes?  The Fox body SVO Mustangs had rear discs with 4-lug.  It's a popular swap to use SVO or T-bird Turbo Coupe rear brakes to retrofit discs to other Fox body Mustangs.  These parts are still pretty common (probably available as a kit).  Might be worth checking to see if they'll fit.
×
×
  • Create New...

Important Information

By using this site, you agree to our Privacy Policy and Guidelines. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.