For Sale
Ads from our classified system. You can reply to for-sale ads in this forum.
1,321 topics in this forum
-
- 1 follower
- 3 replies
- 2k views
A very restorable rear bumper from a 71. There is one ding on the face bar. surface rust on the inside , but not pitted deeply . This is one of the best I've seen in a while. 250 $ plus shipping Early fiberglass series one center console . Has one crack (see pics ). Some of the mounting holes in rear are enlarged slightly. Hard to find these early fiberglass ones anymore 100$ plus shipping email me if interested s_finnerty1018@comcast.net
Last reply by madkaw, -
-
- 4 followers
- 5 replies
- 1.8k views
I have 3 Diesel Cranks willing to part with one of them for that stroker build Its a virgin crank Make me fair offer I am in central canada
Last reply by datsun240z66gt2, -
- 1 reply
- 989 views
I have a 4 speed out of a 4/71 240Z. Is there any interest in these early tranny's? Are they worth any more than the type B? I don't plan on keeping it, but I also am not interested in shipping it. It was pulled from a parts car that was parked due to rust, I am told. So I do not know its condition. It's in Lincoln, NE if anyone is interested.
Last reply by Zed Head, -
- 3 followers
- 7 replies
- 1.9k views
So that others may live... More treasures from the 12/71 parts car, here is a set of 240Z inspection lids with screws and washers. The right side lid has some rust on the underside, likely from exposure to battery gases. The parts are free to a good home working on resto project, I need only the $13.50 postage costs for a USPS Medium Flat Rate box (CONUS only). PM me if interested. Jim
Last reply by wheee!, -
- 5 followers
- 23 replies
- 4.1k views
My 1971 240 Z is going up for sale. I have developed this car for track days and have been modifying it for several years. Tons of goodies and some very nice work has been done to this car. Do not think that this car can be put back to stock, because it cannot. If the car does not sell pretty soon, I will part it out and do it that way. I would like to sell the car as is and all the spares I have which will be listed on an attachment. The motor is not good as I put a rod through the block. However, all the other engine parts like triple Mikunis, hjigh torque starter, aluminum radiator, dual fuel pumps, R-200 rear end with Quaife, 5 speed tranny, fuel cell, etc, etc…
Last reply by Patcon, -
- 0 replies
- 942 views
1973 Dash Air Vent Panel. Super nice condition with one very small chipped edge repair to backlit panel. Backlite harness and bulbs included. Also have the cable lever mechanism. Have plenty of photos. Not cheap!!!
Last reply by David E Roche, -
- 0 replies
- 951 views
1973 Dash Air Vent Panel. Super nice condition with one very small chipped edge repair to backlit panel. Backlite harness and bulbs included. Also have the cable lever mechanism. Have plenty of photos. Not cheap!!!
Last reply by David E Roche, -
- 1 reply
- 1.9k views
1972 Datsun 240Z, fully restored, modified with the best that Datsun can offer. 2.8 liter, triple webers, modified cam, lightened flywheel, Centerforce clutch, 5 speed, LSD rear 3:90 gears, R200, four wheel disc brakes, coil over suspension, Nissan Competition header with twice pipes exhaust, Electromotive crank trigger ignition, 17" custom wheels and tires. This car is fast, Burgundy metallic paint with gold faded stripping. Asking $19,999 OBO. Can be contacted at Multiplex 1@AOL.com
Last reply by JSM, -
- 6 followers
- 71 replies
- 13k views
I have a 1970 240XZ for Sale. Located in Scottsdale. I will send pictures if interested. Vin is HLS30-06026. Car has been garaged for its life. It is original condition including radio and ash tray. Runs great Blue interior Looking to get 8-9K for it.
Last reply by oemz, -
- 2 followers
- 9 replies
- 2.7k views
Free 1970 240z located in Bowdoinham, Maine at Hoyt's Automotive on Rte 125 (right off I-95). This car was a well-maintained summer daily driver for years until the early 90s, then stored in a barn until 2014. Has been at Hoyt's Automotive since then. Jeff needs the space in his lot and plans to junk the car. The car's owner doesn't care, but ok'd my posting the car here as free-for-the-taking. I don't have any photos. I think the color was racing green. Please take it and restore it!! Ask for Jeff Hoyt (owner of Hoyt's Automotive). Was a great car! Thanks, --A friend of the owner
Last reply by dreamscape289, -
- 4 followers
- 29 replies
- 5.5k views
Unicorn: a mythical animal typically represented as a horse with a single straight horn projecting from its forehead. Alt.: a rare Datsun part, usually made of unobtanium. I took this rubber steering coupler from a 12/71 parts car recently. Its in amazing condition - the rubber is flexible and lively, NO CRACKS or other damage, no signs of aging, bolts/nuts are in perfect condition - no thread damage. I've used a wire wheel on the plates and bolts to remove rust, bathed everything in Metal Ready. I'd throw a coat of black paint on the plates but its too cold to paint right now. Offering it here to fellow enthusiasts before listing on any classifieds or eBay. Pr…
Last reply by veejayz, -
- 1 follower
- 4 replies
- 2.2k views
For Sale: L28 3.3ltr short engine. 89mm bore x 89mm stoke = 3322cc Engineered by Les Collins Racing. Built by myself under his direct guidance. F54 block. Acid dipped, 1/2 grout fill, sonic tested & offset bored to 89mm, & finial Diamond honed to exact clearance. Deck milled parallel to crank tunnel centreline. Clearanced crankcase, de-burred & painted in Gyptal. New gallery plugs. Blanked oil pressure relief port. Standard sump & pickup. Modified 89mm stroke crankshaft, oil gallery plugs tapped & plugged. Custom CNC billet steel 8.8kg flywheel to suit crank (no clutc…
Last reply by Lurch,
-
Recently Browsing 0 members
- No registered users viewing this page.
