Electrical
Anything about the electrical system on a Zcar.
3,454 topics in this forum
-
- 2 replies
- 5.8k views
Hey Guys I have an electrical switch under the drivers side dash that the wiring popped out of, I would search it but i don't know what the hell it is. It is rectangular and has the letters HBS on it. 3 wires going to it, GR, GB, and G. Can anybody tell me how this is wired? See attached pic Thanks Frankie
Last reply by Frankensteinz2, -
-
- 17 replies
- 7.4k views
I was wondering if it is possible to use a E12-80 Ignition module on a 77 dizzy? I think I saw somewhere that it is possible, but I don't know how to wire it correctly. If someone knows for sure could they please explain how it wires up. Thanks
Last reply by sblake01, -
- 18 replies
- 6.1k views
Hi all, The FSM for early (1/70) 240Zs doesn't seem to exist and the one for the 1972 model that is available seems to show the wiring to be different from the 1970 model. Is there an accurate wiring diagram for the early 1970 240Z? When I use the search it seems to be able to take only one word and if two are used it seems to use them each separately so that a search on "accurate wiring" turns up posts with either but not both words. Do I have this right? Thanks, Mike
Last reply by geezer, -
- 4 replies
- 1.3k views
When I got my 77 280Z about 2 months now, after a month of using, the starter (3 month old starter) doesn't turn over. Took it to Autozone and they said that the solenoid does not engaging. So I ended up buying a ReMan starter. After about month with the new starter, (which is last night). When I tried starting the car, it cranked for 1 second and all I can hear is clicking sound. So I checked the battery wires and felt that the + (positive) wire was very hot. Checked everything including connections to the battery to the starter. All good. Went back to car and try crank it again, no reaction, voltmeter gauge 0 volts. lost all electrical power and here comes a black s…
Last reply by FastWoman, -
- 2 replies
- 2k views
i'm reassembling my engine bay, and i don't think this is part of anything that's bolted to the walls, but i just can't remember where it goes. it branches off of the harness that goes down the driver's side rail towards the front of the engine bay.
Last reply by MEZZZ, -
- 5 replies
- 3.3k views
Hi all, I want to replace one of the two very large connectors that are on the cable that goes out of the back of the fuse box because one of them broke off. These are the two white wires that go to the battery and ammeter according to the wiring diagram. I cut the crimp lengthwise on the largest connector I could find and tried to crimp it around the stump of the original connector that broke off. I soldered everything but someone who has raced cars told me that solder tends to come apart with vibration. Is there a way to get a really large crimp on connector to replace the original? I already tried Napa and another auto parts store and they just have 12 gauge cr…
Last reply by Mikes Z car, -
- 0 replies
- 1.3k views
So I've been reading for the last five hours sifting though countless threads so if someone who actually knows can you verify this information for me. This is what I understand.... I have an MSD 6AL that I am installing in conjunction with my stock ignition system on my '72 240Z. I haven't done the 280ZX dizzy upgrade yet. Our tachs are a current trigger tach which will no longer work once the 6AL is hooked up. The 8920 and 8910 are tach adapters - the 8920 is for Magetic pickup like the Pertronix 1761 setup and the 8910 is for voltage triggered from the negative side of the coil. In order to get my stock '72 Tach which is current triggered to work I need to use a Chr…
Last reply by FricFrac, -
- 0 replies
- 1.8k views
Ok So I picked up the 280z Today! YAY! Drove beautiful, Over heated in trafic a bit but not to woried about that! what wories is that the car dies out sometimes at idle when stopping! So once it fully Stopped and wouldn't start at all! After I took it home it was a link that was burned out it was in a box right to the battery covered by a white square top there were two wires in there well one of them burned out which was the reason the car wasn't starting! But after that incident the cars RPM gauge and the Fuel Gauge don't work anymore and the Fuel Gauge fuse keeps blowing! PLEASE HELP! The car starts and runs but the fuse keeps blowing!
Last reply by gonshik007, -
- 2 replies
- 1.2k views
I've had a strange thing going with my radio and AC blower for some time, and its now become a major problem. It started a few days after I removed and replaced my dash. When I shut the car off, sometimes the AC blower and radio would remain on for a few seconds to a couple of minutes. I just started up the car today, after not driving it for a couple weeks. The blower motor no longer works. However, when I turn it on, it causes the radio to stop working. The radio won't work again until I turn off the car and turn it back on. I'm hoping this will click with someone, so that I can find a starting place in my troubleshooting. Speaking of clicking, there's a relay…
Last reply by ConchZ, -
- 7 replies
- 2.1k views
HI, does anyone have a part number or brand of the correct battery? Shouldn't it be terminals to the front side of the car with the possitive terminal on the engine side? My battery from auto-zone is terminals to the front with the possitive terminal under the pop-up access panel. thor
Last reply by thor, -
- 10 replies
- 2.3k views
I dunno if if this is normal on the Z. I have a 77 280z. Everytime I start up the car and let it idle, the voltage reads around 13.5v which is I think normal. If I turn on all the lights, a/c, radio, while idling, it reads 12.4v. and if i rev the car up to 3000 rpm, it reads 16-17v. is this normal? or i have a bad voltage regulator? I am new to the datsun scene so I don't know if this is normal. thanks.
Last reply by sblake01, -
- 3 replies
- 1.1k views
Hi all, Hope you don't mind, but now that I am making progress, I will throw out a bunch of questions that are probably simple to answer (this one should be VERY simple). A Chevy V8 guy has a lot to learn about these little Z cars! :stupid: Anyway, can somebody tell me where this wire gets grounded to? I did not pay enough attention when I pulled the engine from the ZX... Thanks in advance! Tim
Last reply by jmortensen,
-
Recently Browsing 0 members
- No registered users viewing this page.
