Electrical
Anything about the electrical system on a Zcar.
3,454 topics in this forum
-
- 16 replies
- 3.2k views
Are parts available for the 280zx electronic distributor in the US? There is very little here in the UK. I'm mainly after the internal magnet.
Last reply by jmortensen, -
-
- 0 replies
- 936 views
Are parts available for the 280zx electronic distributor in the US? There is very little here in the UK. I'm mainly after the internal magnet.
Last reply by Nigel1943, -
The guy kept the starter on the car I bought so I pulled one from another z. If this one doesnt work, Im wondering if I could use a 81-85zx starter on my 76 z?
Last reply by sblake01, -
- 8 replies
- 1.5k views
We just replaced all the carpet in my 78 280....i noticed while tappin on the hazzard swich (mounted on console) the signal lights begin to work and the dimmer switch is now working... Is this possible that all these components are linked in someway.. I was going to replace the dimmer switch for the lights and signals.. Now i dont know what to do.. Please help me..
Last reply by scotts pearl, -
- 5 replies
- 3k views
Can some one provide me with the fuse layout and fuse sizes for my 1973 240Z? Not sure what fuse goes to what in the car or what size they should be,,,, thanks. Dave Rockville, MD
Last reply by wa5ngp, -
- 7 replies
- 1.4k views
My 73 stock has developed some slight gasoline leakage around the gasket for the fuel level sending unit. I've looked at the arrangement a bit and gotten the wires off. Its not obvious how to remove the sending unit. It looks like a simple twist of that ring will get it loose. This does not seem like a very reliable way of securing something that is holding back a full tank of gas. :paranoid: It looks like if I grab that ring with channel lock pliers it would come loose with about a 180deg rotation. Is that right? Don
Last reply by wa5ngp, -
- 1 reply
- 1.3k views
I was given a Crane XR-3000 Points convertor and a PS-91 Coil. I want to install this in my (11/72)-73 240. Does anyone know how it wires up and can I use my Tach. I have read a lot of forums about this and some talk about the tach either frying or not working after the install. I don't have the manual from Crane but have downloaded one, but it doesn't seem to include my setup for the coil and tach. I do know the Red wire from the module goes to the + on the coil and the Yellow to the -, but how does the tach wire in. I have the B/W wire and the G/W wire on the original setup going through a ballast resistor. Do I leave the ballast resistor inline with the PS-91? …
Last reply by mbarjbar, -
- 0 replies
- 1.9k views
Does anyone know if the resistance range on the sending unit on the 240 vs 280 is similar? Reason I'm asking is that I'd like to swap out the combo ammeter/fuel guage on my 240 for the fuel/voltage gauge from a 280z. Hopefully, the resistance range is similar. Reason I'm doing this is that I've routed the ammeter charge wire direct to the battery instead of the thru the ammeter in the car. I had excessive voltage drop coming into and out of the car interior. BTW, I did route it directly thru an inline fuse. It perked up the charge voltage at idle substantially. regards Don
Last reply by wa5ngp, -
- 4 replies
- 4.1k views
Pulled out a Hitachi radio model no. KMS-3611B. This has an 8-pin connector using all 8 pins, and a 6-pin connector using 5 pins. I'm trying to find out what exactly these thirteen wires are. I downloaded a previous wiring diagram, but it only shows where 8 of the wires go. If anyone has a complete diagram, it would be extremely helpful!
Last reply by larryroney, -
- 3 replies
- 1.6k views
hello, I just got a Mallory Unilite distributor and also purchased a MSD Blaster 2 coil. I was wondering, if I need to install the ballast resistor (MSD part number: PN8203)
Last reply by TomoHawk, -
- 14 replies
- 3.8k views
I am planning my restore and came across a Hays ignition that was installed in 76 by the PO. What is involved with reverting back to points and condensor? The first pic below is the ignition mounted on the drivers side wheel well. The second picture is of a box on the passenger side wheel well. Every picture I have seen of other series 1 z's dont have this box (relay???). And the third picture is of the fine paint job that was applied over the gold paint by the PO. It just flakes off in some areas. I wish it would all flake off and get me back to the original color. I am trying really hard to get the car back to all original. Any input would be appreciated. Tha…
Last reply by JohnnyO, -
- 0 replies
- 1.2k views
anyone have a good hazard switch for sale? my car is a 73.
Last reply by nahurry,
-
Recently Browsing 0 members
- No registered users viewing this page.
