Electrical
Anything about the electrical system on a Zcar.
3,454 topics in this forum
-
- 6 replies
- 1.6k views
Ok, so I am looking for suggestions and experince on hiding an antenna inside my Z. I have the following antenna: http://www.ecshylites.citymax.com/catalog/item/604191/368049.htm I went ahead and closed up my antenna hole (it's much better looking and means I don't need to find an expensive replacement antenna). My thought was the area right next to the windshied on the passanger side, but I don't know if there will be enough room. The antenna is 2 feet long and 1/2" thick. I also thought about under the headliner, but I am worried about the reception. Anyone out there mounted something like this before?
Last reply by yukonharry, -
-
- 10 replies
- 1.8k views
Here's the deal. I lost the keys to my car about a month ago. I need to either replace the whole ignition or buy just the key cylinder. Only question is, do I need the key to get the cylinder out? My step-dad thinks I do, but I'm sure somebody knows on here. Thank you.
Last reply by Mike B, -
I've recently had a problem with my car not starting. I mean nothing, like the battery is not even connected. I've checked the battery and it is fully charged however I tried to start it directly from the starter motor across a screw driver, nothing once aqain!? I've heard that these cars have problems with regulators and these symptoms point to it. Any comments? How does the regulator work and where is it? I've provided some pics below of where I think the problem might be!???????????
Last reply by sblake01, -
- 5 replies
- 3.7k views
I'm Just Started Restoring A 1977 280z I'm Installing An Aiwa CDC-X204 Radio AND NEED TO KNOW WHAT WIRES GO WHERE But The Wire Colors Don't Match And I'm Not In Possession Of A Manual For It Yet And I've Been To Two Nissan Dealers But Of Course Their Mechanics Are Too Young And Don't Know About This Car I Need To Know How To Match Up Wires Because The Color Of Wires On Harness Don't Match Up With Wires For Connector That I Have Any Help Would Be Greatley Appreciated AND I'VE NEVER DONE THIS BEFORE HELP PLEASE.
Last reply by TBK1, -
- 15 replies
- 2.6k views
As we all know the stock Zed lights aren't bright enough at all, i initially bought some h4 reflectors off ebay and was going to upgrade the wiring and run some of those "xenon lookalike" bulbs or just high wattage ones, and eventually putting in a HID conversion kit, but after looking at my mates cars with all of the above i realised it wasn't really worth the effort. i was impressed by igor's (007max on hybridz) retrofitting of 5 series projectors and lexus is300 ballasts into some 7" reflectors so i set out to getting some real HID's and a good quality projector lense for myself, either wanting a matching pair off a bmw or honda accord euros, and ended up with some of…
Last reply by zedevan, -
- 7 replies
- 1.6k views
OK, I did the ZX alt. swap with the help of Arne's adapter and excellent directions. As soon as I was able to start the car, a high-pitched squeal eminated from the engine compartment that was NOT there before the swap. Tonight, I got the car warmed up, the squeal was not as intense, but was still present. I noticed, as I was taking the car down the driveway, that the lights would dim (maybe -30% intensity) when I hit the brakes. I looked at the ammeter and it was reading on the negative end of the scale. I tired different accessories, ie windsheild wiper, and the car nearly stalled! The headlights nearly went out, and the wipers froze about 6 inches up the windheild. I c…
Last reply by mlc240z, -
- 2 replies
- 1.8k views
I recently dropped my fuel tank on my '71 240z to get it acid washed and applied the Por-15 tank sealer kit to it and Por-15 the outside, while I was at it I decided to install a new sending unit and O-ring so that I wouldn't have to mess around with the tank for years to come!! All seemed to go well but after about a week my fuel gauge reads either very full or about 7/8th of a tank. I decided to remove the sending unit to see if it would read correctly outside of the tank, I first checked the connections, all seemed well and there were no loose fittings nor any change to the gauge when I jiggled/tweaked them. After I removed the unit the gauge would respond to moving th…
Last reply by beandip, -
- 3 replies
- 1.3k views
I love how some old cars have a purplish tint to their lights. Did they just replace the white bulb with a purple bulb? Anyone got this on their car?
Last reply by cremmenga, -
- 9 replies
- 1.8k views
First post here, hope someone can help solve this. The hazard lights haven't worked since I bought my '77 Z almost 4 years ago. I've gone through the FSM and came up with the following: --checked the fusible links for continuity--~.4 ohms, and power--~12.4 volts at the end of each link; --verified the 10amp fuse in the fuse block is good; --verified I have ~12.4 volts at the hot terminal (red with white stripe wire) of the hazard flasher; --pulled the hazard flasher out of the car, put 12 volts across the terminals and heard it clicking on and off; --tested continuity of the switch per the FSM, and it's working like it should. I'm stuck. Any ideas of what else should I…
Last reply by EScanlon, -
- 6 replies
- 5.2k views
Nobody has really responded to much posts about problems involving 70-71 body harness with 72-73 dash and switches. And I can't seem to find threads on that subject. I have a '71 body and turn signal switch with a '73 dash and headlight switch. The turn signal was inconsistent in operation and headlights would not work. People said that a '72 or '73 turn signal switch would fix the problem. So I got a '72 turn signal switch and the problem was exactly the same. When I turn the key on, the headlights will come on even when the headlight switch is off; turn signals were still inconsistent; brake lights and hazard won't work. SO I assume the turn signal switch wasn't the…
Last reply by yoogener, -
- 1 reply
- 1.3k views
I have a 11/79 280Z fi car. Purchased to get running and resell. The starter, fi, guages were working fine yesterday as I tried to start her after installing new plugs, wires, cap and rotor. She cranked over and all seemed fine then NOTHING! I mean NOTHING! No seat buzzer, no guages, no hazards. Battery checks OK, probe confirms fuses. Should I look for a relay or fusable link? Lee
Last reply by EScanlon, -
- 2 replies
- 1.2k views
on my blower motor ive got the main harness that goes to the blower fan switch in the console....but there are two more wires coming off the blower that i dont know where they go...anybody know or can anybody look for me...ive got a 71 240z with no heat controls and trying to fix that at the moment...thank you
Last reply by aarc240,
-
Recently Browsing 0 members
- No registered users viewing this page.
