Electrical
Anything about the electrical system on a Zcar.
3,454 topics in this forum
-
- 22 replies
- 5.5k views
I am looking for a set of RS Watanabe Rims in black. Either 15 or 16 inch. If anybody has a set for sale or knows where I can find a set, please let me know. Must be in good shape. Thanks Mark
Last reply by EricB, -
-
- 26 replies
- 4.8k views
I have a small problem with my left turn signal I can not seem to run down. The signal has stopped working when I activate the turn signal lever on the steering column. The hazard switch activates the signal and the parking/running lights work. This leads me to believe it is the steering column switch that is malfunctioning. Any opinions??? Keith:tapemouth
Last reply by Mr Camouflage, -
- 0 replies
- 1.4k views
Has anyone had experience with Crane Cams performance ignition? Well i have a 240z with 78 L28 F/I engine and i decided putting in the xr-3000 ignition and the ps-91 coil. I got the coil in fine but i wrestled the xr-3000 all day long and never got it in. It consisted of removing the stock pickup coil and reluctor and replacing it with thier own version thats controlled by a special computer that fires the coil. I had two main problems. The coil wire fired fine...but spark from the spark plug wires would only spark once maybe twice when cranking. I adjusted the hell out of the thing and could not get it to work. The other problem is if you take out the stock pick up coil,…
Last reply by Hallaian42, -
- 1 reply
- 1.9k views
would you by any chance have the diagram for a 83 280 zxt? If not, would you know where to find it? thnaks again for the 240 diagrams, brian 72 240 z
Last reply by Mike, -
- 6 replies
- 2.2k views
does anyone know if the cd rom for sale on this site has 240z and 280zx wiring diagrams?
Last reply by 240brian, -
- 3 replies
- 1.9k views
Here is an easy one (hopefully). Finnally getting around to fixing several things that do not work. Several years ago, after working fine, my heater fan would not turn on with the switch. I presumed that it was as simple as the switch, however someone told me that it was probably the heater core. I do get heat but not from the blower. Any thoughts on this? If turns out to be the switch, does anyone have one available? Nothing on eBay.
Last reply by rcummins, -
- 0 replies
- 1.4k views
During my attempts to get my clock hooked up and running I noticed two short wires with the male ends laying on the floor mats. The ends of the wires were corroded. I checked around some and found that they had broken off where they had been soldered onto the switches or bulbs. This is where age rears it's ugly head. Got them reattached. I can imagine that this could cause a lot of grief and pass unnoticed.
Last reply by ZwolleY, -
- 3 replies
- 1.8k views
I might have gotten over my head a bit, but I went ahead and took off my dash to repair some electrical problems. I was hope someone might have charts or information on where to find wiring charts when i go to put my dash back on. Thanks Frankenstein Z
Last reply by 2ManyZs, -
- 0 replies
- 1.3k views
My 280z 2+2 has left me stranded 2x's now in the last week, just puttin along and everything just shuts off. I can turn key to "on" position and all gauges work and fuse panel shows no blown fuses. I get a faint smell of hot wire from the passenger floorboard for a minute,then clears . The 1st time I had her towed to my Mech, and the recent radiator flush may have left some air in the radiator, coolent was down about 1/2 gal,, thought that the zcar may have just shut itself, but temp gauge was ok? Ran fine for a few days, then it happened again, but when I pulled off to the side of the road, She started up , once again I could smell somthing getting hot like wires or som…
Last reply by boggsy, -
- 12 replies
- 2.7k views
Anyon ever had one dim headlight? My passenger side one is about 25% of what it should be...Bright and regular.... Suggestions? Thanks!:classic:
Last reply by LadyZ, -
- 2 replies
- 1.6k views
O.k.--I believe i have pin-pointed problem. But still have question. From my fuse box I have a white w/black line which runs to a split, one white w/b runs to a relay, the other to a harness connection then into eng comprtmnt into another relay. The lines from split on were melted and in bad shape. When I ran a new line to each of these points and finally make last conn in eng cmprtmnt relay, line wants to fry again. Is it one or both relays causing this or something else???:dead: :dead:
Last reply by Marksz, -
- 2 replies
- 1.4k views
Hi for the last couple of weeks, my Z has had a few hikups, like it coughs and stutters at low revs, but i thought this was because my carbs were stuffed, and i have to top them up with some oil... but i opened up my distributer cap today, and saw a little ball bearing that was not held by anything... i remember the guy i bought it from showed me a stuff one and the little ball bearings were flying around the place.. so i am just asking what i should do.. the car still runs, just when it is cold it coughs a bit, but thats what i really think is the carb tuning, as my carbs are stuffed i need to tune them weekly for them to stay alive etc... its a l26 with 240z carbs, an…
Last reply by Zpeed,
-
Recently Browsing 0 members
- No registered users viewing this page.
jfa.series1
