Parts Swapping
Thinking about swapping parts from another model Zcar?
605 topics in this forum
-
- 1 reply
- 1.5k views
Looking for trades, have an early 5 speed, 3.9 r-200, frame rails, 3 N42 heads, enkei wheels etc. have 260, 280 ,280zxt parts cars. looking for race seat belts, mustache bushings, solid diff mount, 60 mm throttle body, body filler new, 3" muffler, ingnition switch w/key, 1 quart of POR 15. All trades considered.
Last reply by arman1969, -
-
- 1 reply
- 1.7k views
Hey guys! I have a 78 280z and i dunt really like how the bumpers look. I was wondern" if it was posible to put 240 bumpers or maybe the early 260 bumper on my 280? Thanks!
Last reply by ZmeFly, -
- 0 replies
- 1.4k views
I have a 1974.5 260z and have disassembled my car to the bone in preperation for a complete refresh [almost a restoration]. I have stripped the a/c from a 1974.5 2602x2. Is there any wiring changes i should be looking for when I insall the system into my fast-back?
Last reply by sammy, -
- 0 replies
- 1.4k views
I was out boneyard jumping yesterday and found 2 280ZXs. I dont have much use or the extra money at this time. The cars bolth have non turbo motors and 5 speeds. The bodys are shot but look to be all there for parts. One is 1981 the other is 1983. One has black honeycomb style wheels the other has the older finned style alum. wheels. I could see about getting parts if anyone is looking. Just looking to help out. Let me know there less then 5 miles from me.
Last reply by carguyinok, -
- 1 reply
- 1.3k views
is there any differance between the timing chain on a l24 and l28? I am rebuilding an l28 and dont want to have to buy another timing set when I could just swap the brand new one off my l24
Last reply by JEFF, -
- 1 reply
- 1.7k views
I have heard of people putting the late model 15/16 brake master cylinder in their 240Z's. What is the advantage of this and is it a direct bolt on?? dave record 1972 240Z Rebello built 3.0L Tokico springs, rear sway bar, strut tower bars, short steering knuckles,4-piston front calipers, rear disc brakes (brembo rotors),
Last reply by 2ManyZs, -
- 4 replies
- 2.2k views
looking at getting an unlicenced 280z as a donor car for my 71 240z. There seem to be a few 82 model 280's available locally. Questions? 1. Are they fuel injected, should i use it if it is. 2. Are all the parts i need for the diff swap on the 280z 3. Does the 280 motor bolt straight into my 240, can i use the 240 5 speed box (all the local cars are auto). 4. What other parts can i poach off the 280 that will improve my 240. 5.Should I hold out for a different year 280 or one with a turbo motor. ps will keep all my original 240 parts for the time when a full resto is in order. any help would be appreciated
Last reply by sjcurtis, -
- 1 reply
- 2.4k views
I've stripped the rear control arms and strut assembly from a 240z and they look like they'll work on my 260z (The early model). I'm pretty sure the bushings need to be replaced, so for the rear sway bar I need 240z bushings right even though I'm still using my 260z's sway bar? These are the bushings on the bolt connecting the rear sway bar to the rear control arms. I've checked around is Energy Suspension brand bushings good? Or should I just order the polyurethane from MSA? Any suggestions?
Last reply by Bambikiller240, -
- 6 replies
- 2.2k views
This weekend I attempted (key word) to swap my 4spd out of 240 with my 5spd out of my 280. The unistall out of both cars went fairly quickly. I swapped out the rear diff. mounts and then washed both tranny's off. At this point I swapped out the throwout bearings and throwout arm. The clutch pistons I left intact due to the aforemention swap. After jacking the 5spd into posistion I fitted the engine and tranny together and bolted them together. I then bolted the rear crossmember in place. I tried to put the clutch piston in place and then noticed the initial problem. The throwout arm would not move at all. I then unbolted the whole unit and tried to seperate them. This w…
Last reply by Zsled, -
- 2 replies
- 1.9k views
i was looking for a rear end to convert the rear-end of my 72. and one person offered that he have one limited slip differential for $300.00. my first question is is it worth that much? my second question is my should i look for to know that it is not the "viscous type" that they said is not good. i have not seen any of them. what do i need to fit this rear end to my 72? thanks hf240z@yahoo.com
Last reply by Dan Baldwin, -
i am installing an F54 block and P90a head in place of the original 240z motor. My question is the oil pump i am using did not come with the motor. some people say i need a oil pump from a turbo to lift the hydraulic lifter on a P90a head. is it true? is there any way i can differentiate the oil pump for hydraulic lifter and oil pump for solid lifters?
Last reply by 2ManyZs, -
- 9 replies
- 2k views
Does anyone know if puting a 280 Fuel injection system on a '72 240 head is a problem. Sure would like to do it. I have the 280 (1978) in the garage now to take it apart. Any advice is appreciated. - Jeff
Last reply by turbo240,
-
Recently Browsing 0 members
- No registered users viewing this page.
zKars
