Wanted
Ads from our classified system. You can reply to want ads in this forum.
653 topics in this forum
-
- 1 follower
- 4 replies
- 2.2k views
I purchased and restored a 240z steering wheel for my 280z. The seller didn't have the plate for the horn. Does anyone out there have a 240z plate for a 240z horn? See picture for reference. Thanks!
Last reply by Premo34, -
-
- 1 follower
- 7 replies
- 2.2k views
I need the lid spring for the ash tray out of a 2/71 production 240Z. It's the plastic ash tray that covers the fuse panel. Thanks, --Thomas
Last reply by sensench, -
- 0 replies
- 829 views
Looking for an evap check valve for my 77 280. They are NLA and I can't get enough info to cross reference to an aftermarket one. It's the one way valve that sits near the gas tank above the half shaft. Thanks Bob
Last reply by rcb280z, -
I am piecing together an OE stereo radio for my Z I have the radio and the METAL face plate, the plastic face plate is on the way. I have a switch I hope to get locally, really only need to source the mounts that bolt to the radio. I have the U shaped mount that attaches to the console. I did not want to piece this all together but seem the only way to get a complete radio with out spending a fortune on it. here is what I am looking for. one is a simple bracket for just the radio, the other mount to the radio and provides a mount for the antenna switch.
Last reply by Dave WM, -
-
- 1 follower
- 11 replies
- 1.8k views
Hi everyone. Unfortunately the guy who was painting my car lost two of the flat tips for my trim molding (picture attached). I'm in need of at least two of them - does anyone have any for sale? Thanks!
Last reply by misterL, -
- 0 replies
- 1.1k views
I am looking for a few parts for my 1977 280. Parts needed:. Lower passenger kick panel (cut out for fuse box cover and hides wiring "highway"),. courtesy lamp assembly for overhead console (need mounting tabs intact! ...would like to find two / one for spare-future use backup), fusible link base/block assembly (#1 block/forward/towards battery) mine has broken link terminal☹️...I need a block with metal mounting tab intact and male terminals in good condition. Lastly, if anyone has a good, used aftermarket bracket set for mounting 260 bumpers to 77 280. For reasonable shipping expense, would really prefer if I could purchase items 1-3 together. Please e-mail me at dbp…
Last reply by Packerz, -
- 1 follower
- 12 replies
- 7.1k views
My current part's wires rotted away at the base and I haven't been able to find it. Would really appreciate the help. Thanks, Mark
Last reply by Dave WM, -
- 1 follower
- 10 replies
- 2k views
My latest project to keep me out of trouble is fixing up this old signal seeker. Anyone have an antenna switch?
Last reply by hr369, -
- 1 follower
- 10 replies
- 3.8k views
For my 1977 built 260Z coupe, I am trying to put together a complete factory tool kit. I am nearly there, but am looking to purchase a post 08/73 genuine Nissan spark plug removal tool. This is item "10" on the attached fiche image. It comes in two parts, the plug wrench itself and a round-section bar. If anyone has one in excellent condition that they are happy to sell, I would love to buy it. I have a friend in the US, so the part can be sent via him, rather than using International shipping. Hoping somebody can help! Thanks.
Last reply by jerz, -
- 3 replies
- 1.1k views
I'm trying to refurbish mine but the mast is broken and half the internals are missing.
Last reply by JSM, -
- 1 follower
- 13 replies
- 2.2k views
I am looking for the following items (will add more soon): NEW STUFF: - NOS Spark Plug Wires (original 70's style ones) - NOS Fuel Tank Vapor/Vent Lines (Series 1) - NOS series 1 radiator cap USED STUFF: - FRONT driver and FRONT passenger JUTE underpad. (furthest in front of the seats, not behind them- already got those) - Original style A/B Valves (working/decent condition) - Complete Smog Pumps (preferably operating, with as little markings as possible on the main housing/body). - 4.5J TOPY WHEELS (would like to procure a total of 4 or 5)
Last reply by Careless, -
- 4 replies
- 1.4k views
I'm needing the bolts that hold the backing plate on. Just need the ones that are the female receptacles for cover bolts. Sorry don't know what the proper name is. I seem to have misplaced mine somewhere . PayPal ready -thanks s_finnerty1018@comcast.net
Last reply by madkaw,
-
Recently Browsing 0 members
- No registered users viewing this page.
jfa.series1
