Interior
Discussions about the interior components of your early Zcar.
2,371 topics in this forum
-
- 7 replies
- 2.2k views
So my '73 240Z is "out of service" for the winter and as I am bored out of my mind I decide to take a look at my non-working clock. I read a post yesterday about removing the clock through the back of the glove box. So today I go out to the garage and remove the glove box liner and look what I found. The books were in a sealed plastic bag and in perfect condition. It was a nice surprise, much better than the last surprise I found when removing parts. (RUST) The top one is a comparison of AM and FM, one is for the radio (the one in my car) and the consumer information book has acceleration and passing distances in it for all the 73 models. Here is the inside of th…
Last reply by Mike B, -
-
- 20 replies
- 3k views
Hi, I listed my rally clock and oscillator on two diffrent auctions on ebay. The clock is a early rally clock (70-73) which has two knobs on the face. Heres the links. Any questions welcome. btw i didnt know where to post this thread so if its in the wrong catagory please move it where it belongs. Link for the Rally clock Link to oscillator unit/control box
Last reply by bemmerguy714, -
- 18 replies
- 3.4k views
Does anyone either have pictures to post or know of a site where pictures of the various S30 center consoles are posted along with the model years they were utilized? Thank you.
Last reply by 77 Z, -
I'm curious what you guys think of changing the black faces to white gauges in the 240z? I'm thinking of buying a spare set of gauges to do it to so that i can change back at a later stage. The easier to read gauges and blue bulbs would be easier than the black with green lights but it's just not a very period correct thing at the same time. I've attached the gauge set so anyone can download them here and try it out. :classic: guages.zip
Last reply by Murph, -
- 7 replies
- 1.8k views
Hello all, Did a little search and found this thread: http://www.classiczcars.com/forums/showthread.php?t=4066 It was helpful in some ways, but I don't want to just replace my instriment panel lights with regular white bulbs, I would rather go with some blue or red color lights you would see in todays VW's, I just like the look. I haven't been able to find a source for these online. Has anyone else done this change?
Last reply by Arne, -
- 8 replies
- 1.8k views
Ok , all the vaccum lines appear to be connected as they should in the engine compartment. Went over all of them yesterday , made a repair or two as far as old lines that were getting hard due to age, a split in one at the connection, then checked as best I could under the control box for the AC / Heat/ Defroster etc, look as if they are all connected. HERE is the problem , the damper will not close which does not allow heat into the car nor will the defroster work. The blower works fine , have cold air coming in the dash vents but no defroster or heat, there is no sound like the vaccum noise you here when switching from Bilevel or AC to heat or defrost.. Any ideas, this …
Last reply by 77 Z, -
- 0 replies
- 1.1k views
Hello guys, I was wondering if anybody has some extra seats just sitting around...I found out why one of my seats was uncomfortable...it was missing some of the black round spacers! I need 3 of them to make both seats the same height. These are the black six-point plastic 'nuts' that go on the studs that the seats mount to the body with, I beleive stock that the Z (at least my 72) had 2 of these spacers on each of the 4 studs. I need 3 to make the seat the correct height. If anybody has some extras, please pm me. I'm willing to purchase them, if need be. Thanks! God Bless.
Last reply by dogma420, -
- 15 replies
- 2k views
What is the total number of plastic rivets needed for the installation of the 240's interior panels?
Last reply by moonpup, -
- 4 replies
- 1.4k views
between my Z and my g/f's Z, we have enough interior parts to make one good one, which is fortunate since mine will be a club racer and hers will get restored. problem is, the hard plastic panels in both cars are super brittle from age and exposure. is there anything anybody knows about that can be applied to the plastic pieces to reinforce them? a couple panels from her car just crumbled when pulling them out.
Last reply by SJGREEN71, -
- 22 replies
- 2.3k views
I'm helping a guy I know do some small mods to his 280Z because the DMV requires them for safe driving. He also wants to do some shows with the car, and wonders how the judges would react to the extra stuff. opinions? thx
Last reply by TomoHawk, -
- 4 replies
- 1.4k views
these http://cgi.ebay.com/ebaymotors/RARE-New-Old-Stock-Amco-Datsun-240Z-Parcel-Bar_W0QQcmdZViewItemQQcategoryZ42606QQitemZ4610594110QQrdZ1 i've never seeen one.
Last reply by texasz, -
- 3 replies
- 2k views
In order to help the marginal ac performance I am considering applying some insulation under the carpet and wherever I find any dead space between the interior parts and the body. Anyone have a recommended source for this kind of stuff? I bought something like this from JC whitney before but I'm assuming that there's someone that sells this stuff in bulk for a better price. If not then I'll just see what google finds. tks Don
Last reply by 280z1975,
-
Recently Browsing 0 members
- No registered users viewing this page.
