Interior
Discussions about the interior components of your early Zcar.
2,371 topics in this forum
-
- 1 follower
- 2 replies
- 1.1k views
Anyone know of a good source for inner kick plate screws ? Sent from my iPhone using Classic Zcar Club mobile
Last reply by joe newsom, -
-
- 3 followers
- 22 replies
- 4.2k views
Hello, I happened to touch this,my Z432's driver's seat(Right seat) bottom has a stitch in the middle of the front face. But there is no such a thing for the passenger's seat (Left seat) bottom. My seats are original as I have been recognizing so far.But I am not for sure right now.Which one is correct for the early S30? The texture is truely original, seat back and bottom.They have a little scratch but they are very good condition from Jan 1970.I am very happy with my seats. The seat bottom had fixed in some time? How about yours? kats
Last reply by kats, -
- 3 followers
- 16 replies
- 2.7k views
I have a set of new gauge faces for my 1978 280Z, and I started with the clock, since it seems to be the simplest gauge. But, the arms don't want to come off easily, like the pointer for the speed meter will. Is there a trick to getting the clock arms off? IIRC, the speed meter and rev counter pointer will come off easily, and the other gauges (volts/fuel, and oil/water) have enough room under the pointers to slip the labels under.
Last reply by TomoHawk, -
- 1 follower
- 1 reply
- 3.5k views
When Black Dragon was liquidating their parts a few years back, one of the (many) things I bought were replacement rubber pedal pads for my '78. The clutch and brake pedal pads seem to fit fine, but the gas pedal pad keeps coming off. The rubber is thinner than the original one and allows it to slip off from where it wraps around the back. I tried some 3M spray adhesive with poor results. Would weatherstripping adhesive be the best way to get it to stay?
Last reply by zKars, -
- 1 follower
- 1 reply
- 1.3k views
Does anyone know how I could get Amco floor mats for my Z?
Last reply by jonathanrussell, -
- 2 followers
- 6 replies
- 1.6k views
Hi guys, I am assembling the seat belts and noticed the belt that fastened to the top seems to be missing something. To me if I tighten the bolt down it is just going to crush the plastic. Am I missing something? Sent from my iPhone using Classic Zcar Club mobile
Last reply by joe newsom, -
- 3 followers
- 3 replies
- 877 views
This sounds like a stupid question to write, however I am puzzled. Any idea where the jack location goes? Sent from my iPhone using Classic Zcar Club mobile
Last reply by joe newsom, -
- 2 followers
- 2 replies
- 861 views
Anyone know the screw size and where to buy one. Mine is broke off. So I am planning on drilling it and replacing. Sent from my iPhone using Classic Zcar Club mobile
Last reply by joe newsom, -
- 2 followers
- 20 replies
- 4.2k views
Jai (Redwing) found a spring in the drivers side foot well. Looking at the pic she sent it appears to be either the clutch or brake pedal return spring. My guess is clutch spring. A couple of questions. Are the clutch and brake springs interchangeable? I have a good brake spring and the nylon? spring perch from a late 71. Will the late 71 spring work on an early 76 280? Thanks.
Last reply by SoCalJim, -
- 5 followers
- 14 replies
- 1.7k views
I have a broken window roller on the driver's side door. Is this thing repairable (and how?) or should I look for a used replacement? Thanks!
Last reply by zclocks, -
- 4 followers
- 5 replies
- 1.3k views
Anyone know how to replace the felt strips with staples? Or are more commonly glued on? Sent from my iPhone using Classic Zcar Club mobile
Last reply by 52crankman, -
- 3 followers
- 3 replies
- 1.3k views
Anyone know where to source the felt (weather whisker strip) at the top of the door panel for a 1972 240Z?
Last reply by joe newsom,
-
Recently Browsing 0 members
- No registered users viewing this page.
Yarb
