Interior
Discussions about the interior components of your early Zcar.
2,371 topics in this forum
-
- 1 follower
- 3 replies
- 1.3k views
Well, I cleaned up my interior and installed a new dash cap. The problem is... reinstalling the center heat/vent controls. Specifically.. I know the longest cable goes to the fresh air vent flap behind the blower motor... in my infinite wisdom, I didn't take a picture and now cant figure out how it goes back together... simple you say... well I disassembled the "L" shaped bracket and "V" shaped spring, like a dummy. How are they oriented to the pivot? A picture or diagram would be great!
Last reply by Mikes Z car, -
-
- 0 replies
- 1k views
Is it possible to convert my deck 280Z 1977 (earlier) with 45° to a 1977 (late) with flat deck ??
Last reply by denturo, -
- 7 replies
- 1.7k views
I would like to remove what looks like several coats of vinyl paint from some door panels, so they can be repainted with a single layer of paint. Has anyone discovered a good way to remove the paint without harming the texture of the substrate?
Last reply by TomoHawk, -
- 5 replies
- 1.1k views
Could someone please tell me what this hose is for? I couldn't find it in the factory service manual. Doesn't look removable to me (I don't care to remove it anyway), but I'm curious what it is. Thanks!
Last reply by aochider, -
- 5 replies
- 1.2k views
So my seats have been driving me insane. I have restored them, and love having the original look seats in it, but have had issues with the mechanism. The locking side is just fine, and holds well, but the sprung side is way, way too loose, and sags such that my back starts to hurt if i don't put something behind it to keep it from sagging back. What, if anything, can be done about this. I have thought of putting locking mechanisms on both sides, but don't know what others have done to refurbish this, and would love some suggestions. Thank you all.
Last reply by jfa.series1, -
- 17 replies
- 2.4k views
What does everybody use to replace that horse hair looking brown stuff under the seats on 240s? Thanks for any suggestions.
Last reply by tlorber, -
Swell!!.... 1 2
by rcb280z- 20 replies
- 2k views
I just installed, 3 weeks ago, a new full face dash cover. Looks really nice. Now my Tach decides to fail! It's stuck at 2800 rpm. My question is: what is the trick to removing the tach through the front of the new dash cap? I havent spent too much time trying to remove it but it will not come past the "rolled" lip of the dash cap. Anyone else have this issue and found a solution? Thanks.
Last reply by rcb280z, -
- 5 replies
- 2.6k views
I am in the process of restoring a 280z but the hatch support hinges rusted off. I will be welding in new hinges and I was wondering if someone could give me the dimensions of where the hinge is located on each side. Approximately how many inches from the bottom and the top of the rear hatch area.
Last reply by nismospek, -
- 1 follower
- 1 reply
- 1k views
I am trying to change out the old cassette radio in my 1972 Z. My Haynes manual is a bit unclear about that area of the car. I have taken the shift console out and removed the screws holding the big rectangle plate that holds the air/heat controls and the opening for the radio. The aftermarket radio that is now in that area will not slide out the radio opening, it is just a fraction too big. I have that panel loose, but can not see how to get it free enough to work on getting the radio out. The air controls seem to be attached to the panel from inside the dash, but I can not figure out how to get it free. Any advice on what to do next would be appreciated. Thanks, Char…
Last reply by psdenno, -
- 0 replies
- 868 views
Is there such a thing as a lock for the jack and tool bins behind the seats? Maybe a gas-door kind of hardware. My '72 offers little sense of security and I (my wife, actually) would like to feel a little better about leaving things in the car. I understand the concept of "don't" -- just checking
Last reply by NVZEE2, -
- 3 replies
- 4.1k views
I have fabricated a few dashboards and am trying to see if anyone is interested. Here is the dashboard going into my Z. I just covered it with felt for now. The dash will come in a left and a right half. Perfect for the racer or someone looking for something different than a stock dashboard. I also made the dashboard that was in the HybridZ race car. (mock up in my 260Z) The dashboard is not finished and needs finishing. You can cover the dashwith fabric, leather, paint, powdercoat, or polish at extra cost. I can ship the dash with any of these done. It will come sanded smooth ready for a cover if ordered as raw aluminum. I can make a half dash or full dash. …
Last reply by SteveJ, -
- 8 replies
- 4.3k views
The dash in my 1970 Z has the usual cracks (although not so extreme as some examples I've seen other owners post on this site). I'm in the middle of restoring the car's interior and, at this stage, the dash is only a few bolts and connectors shy of being ready to pull out of the car. I've already removed all of the instruments for service and they're now refurbished and ready to go back in. Same for the heater box, radio and centre console. The issue is that I already have a full dash cap ready to be installed. I'm torn between going that route (cap) as opposed to pulling the dash and doing the foam-and-bedliner refinish. I don't expect that I'll ever get this cl…
Last reply by zclocks,
-
Recently Browsing 0 members
- No registered users viewing this page.
jfa.series1
