Open Discussions
Open discussions about the early S30 series issues and topics.
8,810 topics in this forum
-
- 1 follower
- 0 replies
- 554 views
Any of you guys have a 280z blower wheel laying around. I need some measurements of it. I am not going to do the replacement and cut the housing. I have a catalog with a ton of wheels listed in it.
Last reply by ennisdavis, -
-
- 1 follower
- 4 replies
- 1.2k views
Does this intake go to the plenum and if so how does water stay out
Last reply by ennisdavis, -
- 1 follower
- 4 replies
- 2.4k views
Does anyone in the group have any contact information for RSpec Carbon or Paulo Sierra other than their website, Instagram or Facebook? I ordered some 280Z carbon fiber tail light panels from the guy back at the end of July. Product was supposed to ship last week and now he's a ghost. No response to emails, I even reached out to him via his webstore hosting company Shopify. I have my paint and body guys waiting on the parts, and it's holding up my build. Any leads are appreciated. Thank you! - Matt
Last reply by mbz, -
- 3 followers
- 6 replies
- 708 views
Teflon suit on - Check Here goes... Ok, first post here and relatively new Z owner (1.5yrs, 260z 2+2 Auto). The car has weber 32/36 conversion with all the smog stuff removed. It runs decently well, but is rich at idle and takes a bit of cranking (6+) to start if it sits longer than 2 days. It doesn't have a lot of power but I don't really know the baseline. The engine runs smooth, and it definitely pulls ok, but I think it's probably in the 75% range of what it could do if tuned properly. It has a resonator and catalytic converter and original exhaust manifold. I recently switched to non-ethanol and it seems to like that a little bit more, slightly easier c…
Last reply by bartsscooterservice, -
Floor pans 1 2
by ennisdavis- 1 follower
- 18 replies
- 2.4k views
Are 240 floor pans the same as 280 pans? I only see 240 pans on zcar
Last reply by texasz, -
280z battery 1 2
by ennisdavis- 5 followers
- 17 replies
- 6.1k views
What is the exact group designation for a 280z. I have a group 24 battery but its tall and close to the fender. I would like the original battery holder to fit on the top.
Last reply by zspert, -
- 2 followers
- 7 replies
- 786 views
Does anyone make a frame repair piece for this area. Mine is eaten away from the battery on the top of the frame, all the way to the firewall. Do not want to remove the whole frame rail.
Last reply by Namerow, -
- 3 followers
- 3 replies
- 1.2k views
I need to jack up the rear of the car so that I can get under it and turn the wheels. So I have a 3 ton jack under the center support but where can I put the safety jack stands? The rockers and floor are weak and rotted. Are the a-arm pivot shaft strong enough to support the car without bending. I dont see another other place.
Last reply by CanTechZ, -
- 3 followers
- 10 replies
- 1.7k views
Can you guys help me id some of these parts?
Last reply by zspert, -
- 7 followers
- 85 replies
- 7.2k views
does it look familliar? its not a mc guard... on my 260 tried a socket hammered on - cant get these locks of.. help!! photo 3 shows the splines....
Last reply by CanTechZ, -
New Member 1 2
by SupremeCling- 2 followers
- 13 replies
- 1.2k views
Hello, My name is Seyler from Colorado, and I am an S30 addict. I am glad to finally be here, as I now own my first S30, a Black Pearl. While I have fed my addiction on my own for some time, I know I will need help to manage my addiction. I only hope to be able to pass along the help I receive to those who will also need help with their addiction in the future.
Last reply by SupremeCling, -
- 1 follower
- 0 replies
- 562 views
Do all 75' 280z's use the 8 1/2" booster?
Last reply by ennisdavis,
-
Recently Browsing 0 members
- No registered users viewing this page.
jfa.series1
