Help Me !!
This is the emergency HELP ME forum for those of you that are having troubles with your Z-Car and need immediate help.
6,114 topics in this forum
-
- 10 replies
- 1.6k views
I have a 1980 10th anniversary 280zx automatic. This is a CA car with 98,000 miles and up until now has been running great. Now when I accelerate I feel a hesitation in the engine like it is holding back, when I give it more gas it sometimes responds and other times hic cups a couple times and pops. A couple times it has stalled out when just making a slow turn. also (this is new) while running at 70mph the tach has dropped to zero and stalled out then picked up again. this now has happened 4 times and the last time it stayed off for 15 seconds or so and then started up again. anybody encountered this previously? No idea what it may be. Maybe dirt in the gas tank?
Last reply by big mike, -
-
- 2 replies
- 1.1k views
door latch needed 74 260Z 2+2. the driver side door latch I have has broken the spring and will no longer latch. Looking to buy one. Hope some one out there has one they are willing to part with. Thanks.
Last reply by flannelman, -
- 3 replies
- 1.2k views
hey guys, i just bought a project z car. im in the process of fixing the clutch. i get fluid from the master to the slave cylinder but its just not disengaging the clutch, and the pedal feels ultra light like theres no pressure. do you think i need a new slave cylinder? or can i fix the one thats on there? thanks guys!
Last reply by olzed, -
- 1 reply
- 1.3k views
Hi all, I am new to this forum and those in it and I wish this first post was under better circumstances. I will try to be as clear as I can be here just please have a heart and skip the RTFM responses, thanks in advance. My father owned a 73 240z and he passed away last week. The car had been a project we were working on and I am trying to get it running to take to the funeral on Thursday night (June 14). One of the things that was done on the car was the carbs were replaced with reman units from ztherapy. We were able to get the carbs installed and somewhat adjusted last fall, at least to the point where the car runs and I was able to drive it to my house to store f…
Last reply by zKars, -
- 6 replies
- 6.6k views
I just wanted to confirm that the engine and transmission can be pulled as a unit. Radiator's out, of course. I thought I installed it assembled using a load leveler by myself, but that was 12-13 years ago and my memory isn't always accurate. 8( The engine is being pulled tomorrow so that's why I posted here. Thanks for your help! Dave
Last reply by 240260280z, -
- 2 replies
- 1.6k views
Installing exhaust pipes on MSA3-2-1 header. Does the short straight pipe go on the collector first or the longer slightly bent bent pipe go on first?
Last reply by 2Forty, -
- 9 replies
- 1.5k views
The Problem: What started out as an intermittent power loss during acceleration has progressed to nearly a constant problem including at start up. I am now relegated to starting the car in the driveway and an occasional trip around the neighborhood. It does however has it’s moments. Just 2 months ago after not starting it for a couple of weeks, it started up, idled smooth and revved up smoothly so I took it out and it didn’t act up so I took it on the closest highway and had it up to 80mph and had a lot more but was afraid of getting a ticket. The total trip was only about 30 minutes, I was elated. Decided to try it the next day and it acted up on start up. This has b…
Last reply by AZ260Z, -
- 0 replies
- 1k views
Can anyone recommend a good mechanic in Las Vagas, that could be trusted to know what he's doing with a 350Z? Contact info needed thanks, Carl B.
Last reply by Carl Beck, -
- 6 replies
- 1.4k views
I drove my 73 from my old house to new house. Replaced points with Pertronix ignition and flamethrower coil. 3 wire tach wasn't working and replaced that as well. Car starts but dies when key is released to run position. All fuses are good. After said problem I replaced solid state voltage regulater with stock voltage regulator with same results. Any ideas?
Last reply by 2Forty, -
- 0 replies
- 811 views
Hello all This past weekend I did a tune up in the old Z, new plugs, new wires new rotor. (the cap looked new). I have a MSD Blaster II coil along with a ZX dizzy (81 I believe). I'm having a miss fire under really all conditions and haven't been able to figure out why. I've checked the gap, resistance of wires (and the cap) along with the coil. Is there a way to test the "match box" (black box) on the ZX distributor? Thanks all Jan
Last reply by Pomorza, -
- 5 replies
- 4.5k views
Hello, forum! I unbolted all the bolts to get both the shock mounts off my 1976 280z but I cannot get them out of the whole. Am I suppose to cut the thing or is there a way to take it apart?
Last reply by mi3nboijosh, -
- 3 replies
- 1.4k views
I need to replace the diff on my 240z i think it was swap by a previous owner. These picture are from my 1971 240z and i figure that the way the mustache bar is mounted my diff is a R200. Anyone can confirm this would be realy appreciated Thank`s Jean-P
Last reply by jeanp,
-
Recently Browsing 0 members
- No registered users viewing this page.
Yarb
