Help Me !!
This is the emergency HELP ME forum for those of you that are having troubles with your Z-Car and need immediate help.
6,114 topics in this forum
-
- 4 replies
- 1.1k views
I need to know how far the brake pedal should be traveling. I've been getting ready to take the Z out into the spring-time weather during the past week or so, and so I took an opportunity, as I'm sure we all have done at one point or another, to sit in the driver's seat and just visualize... Anyway, for one reason or another I ended up depressing both the clutch and brake pedals. The clutch will go to the floor... but the brake pedal seems oddly stiff. It seems like I can only push it down a few inches, and I can't tell if this is normal or not. I remember the Z having very "tight" brakes in comparison to both of my parents' cars (especially my mother's Honda, which feels…
Last reply by KDMatt, -
-
- 4 replies
- 1.2k views
I just rebuilt my z engine. I have a 77 but the engine came out of a 78. I am trying to figure out the wiring diagram I cant remember where the wires are that go to the Distributor? Any one that can help would be very thankful.
Last reply by Armypilot, -
- 0 replies
- 2.5k views
Does anyone know what the part # is for a 78 thermo time switch. I dropped my thermostat housing and the connection broke:disappoin . I was testing it before it broke and I wasnt getting good readings anyways and on top of that the bolts broke of in the bottom thermostat housing part, if its not one thing its another:sick: . The #'s on mine are A23-601000 and it says 19.5 degrees C and 9 sec. It also has 9315 and JECS on it. I just want to know if this is the right thermotime switch. Thanks
Last reply by 78 280zcar, -
- 4 replies
- 1.4k views
I have tried to locate a hood release cable for my 1978 Z. I can't seem to find one. Can any one please tell me where I can locate one.
Last reply by First Gen Z, -
- 1 reply
- 1.1k views
This is a "Help Me" cause I can't drive the car and my truck is on it's last leg. Need right hand tail light 3 wire socket for brake and brake light, it's a 78 but I think any Z will work(someone know off the top of their head?) "My" parts car at the junk yard has been crushed. Anyone have a parts car laying around that can send this to me? I was going to find the problem with the light and the socket acted like it had a small bomb in it when I twisted the bulb out. PM if you will, will PayPal you for socket and Express Mail. Thanks in advance.
Last reply by LanceM, -
- 6 replies
- 1.5k views
My early 260 is giving me fits.The problem is a wierd one to nail down. The car starts right up then in 5 to 10 seconds it dies? Ok sounds like fuel delivery Nope guess again! The bowls on my 72 carbs are full. Both fuel pumps are working 5 pounds of pressure at carbs. Brand new filters, lines , Z therapy carbs Ive tested the ignition circuit at every point i can find per the fsm and 3 other books on this car.Seems ok.It does have the early 74 ign system. Maybe i should upgrade to the 79 80 ign system.Lots of parts on the old one .
Last reply by cremmenga, -
- 13 replies
- 4.9k views
Is there a big difference between 1980 flat top pistons and 81', I looked up piston rings for both years and there is a difference between the rings. The 80' one uses the same rings as a 78, but the 81' uses the same rings as an 82'. The reason I ask is because I am buying some flat tops off of someone on this site but am not sure if they are 80' or 81' flattops. I was hoping to use the same rings from the rebuild I have already done but am not sure if I can. Thanks
Last reply by 78 280zcar, -
My 77 now only blows out of the center vents. I took the dash apart replaced all vacuum lines and checked cables. How do I continue to trouble shoot what is probably a vacuum / solinoid /diaphragm (bottom of blower motor) problem?
Last reply by mriz, -
- 0 replies
- 1.1k views
I just replaced my auxillary air regulator to solve my problem of high idle when coasting but now I have a new problem. The car now emits black smoke and coughs and sputters while trying to drive (just around the lot). This problem didn't exist before we replaced the air regulator. What is causing this new problem? I just put new plugs in today and it's still running rich.
Last reply by mholmes, -
- 2 replies
- 1.4k views
how much of a pain would it be to change out a gear shift lever that's been cut?
Last reply by T's 280z, -
- 10 replies
- 2.7k views
This is the second time I have posted this. There is a place in virginia (chesapeake) called East Coast Z, its a Z junk yard. Barry is the owner and has over 400 Z's to choose from. His prices are fair and he ships to anywhere. Give him a call @ (757) 543-7168. Hope this helps. Ken wing
Last reply by KenshinX, -
- 4 replies
- 1.3k views
82 280zx turbo... runs fine... new alternator and all new fuel system components along with cap and rotor, plugs and wires. car starts up good and idles fine in park. u can rev the engine and everything it all sounds nice. then u put it into drive and give it some gas, it moves boggingly a few feet then dies. car starts right back up and is accompanied by a squeeling noise when u step on the gas....sounds like alternator belt. the squeeling doesnt go away till u put it in drive, give it some gas, and the car instantly dies. ive heard this could be the transmission modulator.... anyone had a problem like this??? i really need help
Last reply by Zedrally,
-
Recently Browsing 0 members
- No registered users viewing this page.
slogan5
