Help Me !!
This is the emergency HELP ME forum for those of you that are having troubles with your Z-Car and need immediate help.
6,113 topics in this forum
-
- 8 replies
- 1.4k views
I bought this shifter boot for my 280z. http://www.courtesyparts.com/Merchant2/merchant.mvc?Screen=PROD&Store_Code=CP&Product_Code=32869-S30 But when it is in neutral it pull the boot up, is it suppose to be like that or no. I finally got my engine back together havent got to run it yet, I am a little scared to start it because I put 3000.00 into the engine and to have it not start would really upset me. I will post some pics of it tomorrow and pics of the shifter boot to see what I am talking about. Shane
Last reply by 78 280zcar, -
-
- 5 replies
- 1.6k views
yesterday morning a got in mt car to go to work. It is very cold natured( probably due to thirty-two year old su's)and i was running late. i hopped in my wifes car and went to work. she called me later to tell me my car ran into my neighbors house. Ouch. i think my ebrake gave out or maybe i forgot to set it, cant remember, too early. anyway it dented my rear quarter all the way to the finderwell. it still drives good and not out of allignment but it is pretty bad. how should i fix it? is it hard to replace the whole Quarter pannel?any advice is welcome. THNAKS
Last reply by andrewg3300, -
- 13 replies
- 1.9k views
Hey guys, I'm cleaning my vents. The two round side vents were easy to get out. How do I get the center dash vent out without breaking it???
Last reply by 26th-Z, -
- 8 replies
- 1.9k views
When I bought my 280zx, it had a problem, that it would cut off randomly while driving, the tach just shot to zero but you can still hear the engine running. So I thought it was the Ignition module, also note, that the plug that is on the side of the IM if it was unplugged it made no difference to the cars running, it just ran fine until it cut off and it took a while to start up. Today, I got my IM in the mail, I go install it and right away it has a lumpy Idle, I take it out make sure everything was connected properly and still lumpy, I install the old one it takes a while to start but it runs smoother. I put the new one back in and then it still idles lumpy but it star…
Last reply by djbess, -
- 9 replies
- 1.6k views
Hi everyone. I am in need of a good passenger door panel for 1970 z. Needs to be black and needs to be very nice shape. Does anyone have one for sale or know where i can buy? Thanks
Last reply by code3z, -
- 21 replies
- 6k views
I finally got my car on the road, but my rotors are warped. I bought new rotors and pads, but I cannot get my old rotors seperated from the wheel hub assymbly. I have used PC Blaster and wacked it with a large hammer (using wood blocks) and I cannot get them seperated. I have removed the 4 bolts that hold the two together. Has anyone had this problem? What should I do? Do you think I can have them pressed apart? My local dealer said to use a bigger hammer. Any help will be appreciated. Thanks, Mark
Last reply by MarkDixon, -
- 0 replies
- 1.1k views
I manage to figure at my last issue and now I am getting spark to the coil,car still wont start ,I don't seem to get power to the fuel pump(tested it with a test lamp)I jump the fuel pump and it started for a bit.What and where do I start in tracing the wire's from the fuel pump?Check all the fuses(good),check the ig relay work's,what is left?
Last reply by rcperez123, -
- 9 replies
- 1.3k views
Well I finally got everything back together on the engine and was getting ready to put the tranny back on to stab the engine back in, when I found out that the tranny cover (behind flywheel) I had for my automatic doesnt work for a manual tranny :stupid: . Well now I am in need of that plate if someone may have one that I can buy please let me know!
Last reply by 78 280zcar, -
- 8 replies
- 1.5k views
Since there seems to be a lot of electric fuel pump questions being bandied about, I thought I'd add mine to the mix. I have three (count'em, three) electric fuel pumps from various ZX's that all run (i.e. motors run fine when hooked up to to a battery), but don't/won't pump gas. (I figured I'd test them BEFORE installing them, to save myself some grief). Figuring that there must be some crud builtup inside the pumps, or maybe cracked or worn out o-rings, I dissassembled one. The pump itself is an extemely simple design, consisting of a rotor with 5 cylindrical "pellets" and two 2 o-rings. The o-rings looked fine and there was no varnish or crud inside and the check va…
Last reply by peterc, -
- 24 replies
- 8k views
Hello I picked up a 9/70 Z and the previous owner said he put the battery terminals on wrong and fried something? The starter works and that fusible link is fine, I have lights gauges etc. but no spark. It has a magnetic pick up dist. with the numbers D6F4-03 7303 22100 N4301 marked on the side. It has vacuum advance and the wrong timing plate/base? The spark box is mounted on the firewall with HITACHI E12-12A marked on it. It has an 8140 Accel 12v Super stock coil. The previous owner said his brother put it on so I assume it's installed wrong or don’t work? Here are some pic's of them maybe someone can identify them and suggest the correct installation or some t…
Last reply by 240zwinter, -
- 4 replies
- 1.3k views
I picked up an '83 280ZX non turbo for my nephew. Is the injector wiring color code the same as on an '82? Also, are the turbo injectors the ones with the little nipple on the end of the injector? I'm trying to find out if these injectors are from a turbo or non turbo. Thanks for any info you can give me...
Last reply by fisherman338, -
- 31 replies
- 10.1k views
im having troubles keeping charge to my 280. i had the battery and alternator checked. the starter also. whats happening is i have to jump the car. once its started and im just sitting there idleing its fine, but once i drive for a while my battery starts to die as if the alternator isnt helping it. i checked one of the fusible links and it was dry rotted so im guessing the others are too and they all need to be replaced. would that make sence for whats going on? if im right... where can i get the links. or is there a amp fuse i can use and just get rid of the wires? my e-mail is tim_7_2000@yahoo.com any and all info is helpful! thanks
Last reply by slaptimmay,
-
Recently Browsing 0 members
- No registered users viewing this page.
Yarb
