Help Me !!
This is the emergency HELP ME forum for those of you that are having troubles with your Z-Car and need immediate help.
6,113 topics in this forum
-
- 1 follower
- 7 replies
- 1.1k views
I have located a bumper for Cody's car just outside Eugene but the seller doesn't want to ship. If anyone could help me out and get the bumper and ship it to me, I would cover the shipping and try to compensate for the time it takes. I am pulling stuff together for his 18th birthday presents later this month. Thanks, Charles
Last reply by DamonR, -
-
Measurements
by Dude- 1 follower
- 2 replies
- 882 views
I need to weld it in my camper plates on the front and back strut towers of my car I wanted to know if anybody knew the measurements from the center hole of the strut towers from right to left of the engine bay and the rear strut towers ?
Last reply by Dude, -
- 1 follower
- 1 reply
- 834 views
whats the best option for inner hatch weatherstrip 12/72 build date 73 Z have later NOS nissan different from original -have an older persion not even close not worried about originality just want to get something that works tired of buying weatherstrip that doent or insnt going to work so before i buy anymore weatherstrip does any one know something that works new- datsun -parts says they have a repro close to original - vintage rubber anyone use that one im not opposed to a push on from a kia or acura or any other brand im not opposed to a universal push on i know there are a lot of threads on this but most dont seem to be definitive …
Last reply by EuroDat, -
- 1 follower
- 0 replies
- 781 views
I've never used the "help" page before , but for reasons detailed in my posts under "Electrical" I've got an issue with windshield wiper drive, and I have to get it fixed much sooner than my limited diagnostic skills
Last reply by Richard McDonel, -
- 2 followers
- 4 replies
- 1.5k views
Gents, Making progress on my 280z. I am replacing the carpet now but need to prep the floor. A few questions for the experts, I’ve looked over historical threads and see conflicting into. 1. My floor pan are solid with only mild surface rust just around drain holes. I’ve read people removing the sound proofing before installing new sound proofing matting and carpet to make sure there is no rust under the old stuff. Is this necessary? With not visible rust anywhere seems like a lot of extra work. I haven’t found any rust on the car anywhere so far even in the most likely areas. 2, I was going to clean the drain holes with some naval jelly to stop …
Last reply by SoCalJim, -
- 1 follower
- 7 replies
- 1.1k views
I have a re-bodied 240Z. The VIN says it is a 1973. After a couple of years of restoration it is now on the road and shake down has begun. I discovered the right rear strut was leaking so I started looking for replacements. Am I correct that a '73 has a straight axle and if so then what do I have in my car. See pictures A separate but related issue is the from struts. I would like adjustable one there because the nose of the car is sitting too high. I look forward to your help. Harvey
Last reply by Patcon, -
- 6 followers
- 24 replies
- 4.4k views
Im new to forum and new to the 240z. Recently purchased a 71 240z bone stock L24. Im upgrading the 60amp alternator and have followed the DIY. Seemed easy and straightforward. Tested alternator to ensure its working well. Tested battery also good. I modified harness and eliminated old regulator and covered harness socket. L to 12v source via fusible link white wire and S to b/W (SWITCH 12V) with diode. Diode line faces alternator. Everything good so far. Here is what happens. Tested while running with volt meter battery and read 12.6 (not good) I remove negative cable from battery and it reads 14.5(good) the alternator sounds different meaning regul…
Last reply by Mike, -
- 1 follower
- 4 replies
- 1.2k views
Hello, I started the car the other day, it was hard to start, but it idled fine. Took it for a drive and i saw the amp meter dropping to 8 and oscillating violently as well as the car sputtered and could see the rpm dropping real low. Looked at all the ignition stuff and saw the condenser wire had broken off. I have a parts car and took the condenser form it and it still does the same thing. I am unsure of the condition of the parts car condensor, its been sitting for over 20 years. Parts are not available, i bought a 22 microfarad condenser from another car in hope to see if it works. ANy suggestion?
Last reply by kutukutu1, -
- 1 follower
- 7 replies
- 1.1k views
Does anyone know the size, length ,and pitch of the bolts that hold the bracket for the compressor on in L24 engine?
Last reply by Dude, -
- 2 followers
- 11 replies
- 6.2k views
Hey mates It appears that the one piece rubber outer hatch seal - the thin one that goes outside - is broken an allowing rainwater in. I've had issues installing these in the past - I've broken two right out of the box when I shut my hatch. Is there a special way of doing these where they don't break? Is there any rubber seals I should avoid? Any place to get OE ones? Cheers Jan
Last reply by jfa.series1, -
amco parts 1 2 3
by Taz0162- 1 follower
- 26 replies
- 9.3k views
Does anyone have a source for the Amco parcel bar accessory for a 1972 240z? not interested in the bumper overriders or the passenger foot rest but like the idea of the parcel bar.
Last reply by Taz0162, -
- 2 followers
- 8 replies
- 1.5k views
Hello, I amsearching for rubbers of the front and backaxle (see attachment). Where can I buy them= What is the partnumber of tese rubbers?
Last reply by Zup,
-
Recently Browsing 0 members
- No registered users viewing this page.
