Body & Paint
Discussions about bodywork and painting a Zcar.
3,662 topics in this forum
-
- 5 followers
- 6 replies
- 1.3k views
I decided to create a new topic to continue the discussion regarding factory undercoating and whether primer / paint was used or not. I understand and it makes sense that the factory may have done different things over the years with regard to undercoating so all I can really present and comment on is my 5/72 240z. I would really like to see what @Carl Beck, @26th-Z, @bluezand others think about what I am seeing with my car, relative to what has been written and thought about the topic over the years. My car is a 5/72 240z. It has original 918 orange paint that is in excellent condition. The car shows approximately 24k miles and in every way that I can thin…
Last reply by bluez, -
-
- 3 followers
- 10 replies
- 1.5k views
Hey Guys, what is the best way to take these off? i am planning to get the car painted. I tried access them from inside by removing the inner panels but no luck. Looking at the new ones they have 3 pins. Should I just use a heat gun and pry them out with a screw drivers? They are a bit beat up too!!!
Last reply by siteunseen, -
- 2 followers
- 6 replies
- 1.5k views
Hi , I have been unhappy with my 240Z’s bonnet. The top center edge was pointing down quite noticeably. I wanted it lifted up as we have seen it in original, un damaged bonnet. All I have seen old pictures show me beautiful, a bit far from the bumper than the both left and right corners. So , I did it by my self . It is a crazy thing , It was abrupt method. I used a jack with wood pieces to push the top center of the bonnet. Gradually and carefully lifted it up , I was so scare when I was doing it . It turned out quite nicely, I must say I am happy with it. I don’t see any crack or bumpy , shrink surface . I will do some bonnet hinges adjustments, also ma…
Last reply by kats, -
- 1 follower
- 1 reply
- 491 views
Is there a place or publication that I could look for that has an exploded view of a 280Z body ? I'm interested in the disassembly of the front of a 280Z ? I have a 1975 Factory service manual, but it doesn't give you a disassembly sort of view or illustration ?
Last reply by Patcon, -
- 6 followers
- 12 replies
- 5.7k views
DISCLAIMER: I did this on a '71 240z - I cannot confirm this works for later models. Preliminary Notes: In searching for new weather-stripping, I came across many forum posts recommending late 90's to early 2000's Kia Sportage weatherstrips. In some of the comment sections there was mention of McMaster-Carr, and one thread dedicated entirely to this stripping. I followed exactly what the guy did in his post, so I am ripping him off, however I thought it'd be worth making a post of my own not only to back up his findings, but also to (hopefully) give this weatherstripping a bit more publicity. Now, I originally had Precision's weatherstripping set, h…
Last reply by Tweeds, -
- 2 followers
- 3 replies
- 539 views
What is the difference between the front windshield gasket between a regular coupe and a 2+2 sedan ? I can see the rear hatch, but the windshield on both the coupe and the 2+2 version, they look the same ? and is there any real difference from a windshield of a 1970 or a 1978 ?
Last reply by Killain, -
spray guns 1 2 3
by Patcon- 7 followers
- 27 replies
- 2.6k views
Having bought some more paint recently at eye watering prices, I am considering getting a pro level gun. Tried to do some googling but kept finding the same useless info. Does anyone have any recommendations? Sata, Iwata, DeVilbiss, Tekna, etc...
Last reply by Patcon, -
- 1 follower
- 15 replies
- 3.8k views
Good news is, the tail light gaskets on my 72 are in very good shape, they look just as good as the brand new ones I ended up leaving in their wrapping. Bad news is, the lights aren't as fortunate. Anyone dealt with this before? Any advice would be good, be it replacing the lights, using some sort of filler between the flange and gasket or just about anything else. The metal overlay trim that fits over the lights is in great shape so I'm not sure how they got so bad, but speculation won't get me anywhere. Thanks, everyone.
Last reply by Daluvian, -
- 2 followers
- 4 replies
- 630 views
I was in the process of removing my fenders to clean out the dirt underneath and check for rust. Then I realized these side skirt things I have are riveted on, smh.. Guess the only way would be to drill the ~20 rivets out through the body, just curious if anyone else has this piece installed? Maybe it was a dealership option or a previous owner did it, but what a pain..
Last reply by S30Grit, -
- 3 followers
- 7 replies
- 1.3k views
1973 240z Looking to see if someone could measure from the inside center of the spare wheel to the tail light panel center? Also a pic of the backside of the tail light panel like the ones in pic and underside it would be greatly appreciated! Looks like someone replaced the panel and not sure if the underside is supposed to be spot welded looks like a gap there everything lines up fine on outside debating if I should leave it or repair it. If anyone has any advice or experience let me know Thank you
Last reply by Daluvian, -
- 1 follower
- 1 reply
- 736 views
Guys, took the two bolts out holding the front side rubber bumpers to the main front chrome bumper. Rear end of the side bumpers is help to the body near the side markers by something which i cannot locate from inside. I am hesitating yanking it out. What is that holding them?
Last reply by MH77280Z, -
- 1 follower
- 0 replies
- 550 views
The resurrection project continues to creep forward. I have just begun cleaning up the firewall and installing a couple of small patch pieces for minor rust through areas. I have all new grommets but noticed what appears to be some type of soft sealant around the firewall holes. Was there originally some type of adhesive/sealant around the grommets, cylinder mount areas? If so ,would the 3M product # 3602-black super weatherstrip adhesive-be good choice. I have used that messy stuff with good success on other areas with weatherstripping, etc. Or, should we just install the grommets as is and call it good? Thanks again for any input, John-Lugoff, SC.
Last reply by One Way,
-
Recently Browsing 0 members
- No registered users viewing this page.
