Body & Paint
Discussions about bodywork and painting a Zcar.
3,662 topics in this forum
-
- 2 followers
- 29 replies
- 4.3k views
Howdy, I’m trying to flush mount a rear early 260z bumper to a early 260z. From other threads I have read that you can drill out a leak hole for the oil, the push the shock inward and weld it into place. I drilled a hole in the strut l, drained a significant amount of oil out of the strut, but the strut does not stay depressed, it seems like it keeps popping outward. I beat on it with a dead blow hammer, I can see that it moves inward then comes right back out. Is there a trick to this that I’m missing?
Last reply by Freez74, -
-
- 1 follower
- 3 replies
- 1.1k views
I own two S30s and am an original owner of one of them, for which I have been in the process of doing a restomod for several years. I am also a retired R&D chemist with a background in plastics and rubber chemistry and processing. I have been frustrated several times regarding the various small rubber bits that go into my S30 as, I'm sure, are many other owners of old Datsuns. Many rubber parts are simply "no longer available," at least through the Nissan parts system. With the closure of Black Dragon a few years ago, the situation got worse. And, some of these NLA parts, especially those approaching 50 years in service, are simply "tuckered out" due to the h…
Last reply by Patcon, -
- 2 followers
- 11 replies
- 978 views
Apparently finding a 240z one of these is almost impossible. I bought one like this https://www.ebay.com/i/154082623242?chn=ps&norover=1&mkevt=1&mkrid=711-117182-37290-0&mkcid=2&itemid=154082623242&targetid=935065066707&device=c&mktype=pla&googleloc=9027875&poi=&campaignid=10455978145&mkgroupid=104612009660&rlsatarget=aud-412677883135:pla-935065066707&abcId=2146002&merchantid=6296724&gclid=Cj0KCQiA-rj9BRCAARIsANB_4ABVTQhdVz8OWxC8AhTcoPeDTnylMx9pWoWTsRy0Ldb6K-qjkLifIb0aAqfCEALw_wcB Already tested it and it works if you are willing to 1. saw arm button in half like image below. 2. weld arm…
Last reply by Racer X, -
- 1 follower
- 1 reply
- 1.8k views
Does anybody have a video showing how to install chrome trim around hatch and windshield? Or any instructions or tools i need. Also, does anyone have a source for replacement pieces? Stainless is fine...just not wanting to pay $400 for one set...seems too high
Last reply by jfa.series1, -
- 4 followers
- 12 replies
- 3.1k views
I just watched a video of a 1976 280Z barn find that has just 350 miles on it. My daughter recently bought a 1976 280Z project car that is the same color (light blue). We’ve been working on her car and it will be getting paint this month. She wants to keep it the same factory color so I had checked a few different internet sites and all indicated that her car is painted Light Blue Metallic #305. In the barn find video they are taking about how pristine all the factory markings are and they showed the paint code decal. It says the paint code is #304. When I saw that, I went back to some of the sites I had previously looked at for paint codes and all of them indicate t…
Last reply by grannyknot, -
- 2 followers
- 12 replies
- 4.9k views
Before media blast/epoxy primer, I tried to get the ebrake clips off but had no luck...figured I'd wait until it was blasted and on a rotisserie to pull them out. Well, that's all done and still no luck. I just can't seem to get enough of a grip on them or any sort of pivot point on a prying implement to get them out. I'm hoping that someone can give me some tips on how to get these guys out. Thanks!
Last reply by adivin, -
- 1 follower
- 4 replies
- 654 views
Good morning. I am hoping to get some opinions on these taillight panels as I am trying to decide whether they need to be returned. In relation to the car, the outer panels do not meet the upper lip on the hatch area (elevation) and do not engage fully. Even if they did, there would not be enough material to catch the screw holes. In relation to each other, the center panel is nowhere near seating neatly to the outer panels. I was expecting that they may be a bit fussy, but I'm not sure if this is a workable starting point. Thanks in advance for the feedback, Robert
Last reply by grannyknot, -
- 1 follower
- 2 replies
- 836 views
I'm getting ready to put some Euro bumpers on my 73. Found the unused mounting points on the frame, should be good to go after chasing the threads out. Bought a pair of 70-72 brackets, but not sure which bracket is for the left or right. Looks like the frame holes are offset a bit and may raise or lower bumper a quarter inch or so. I searched, but came up empty. Which is which? Or does it matter? Thanks
Last reply by siteunseen, -
- 0 replies
- 507 views
Last reply by 240260280, -
- 3 followers
- 7 replies
- 1.1k views
I need to buy panels for the left and right side below each door handle... is this called the rocker panel? I usually buy from Z Car depot but i dont see anything there. I might be calling it the wrong thing? thanks
Last reply by Wally, -
- 3 followers
- 5 replies
- 789 views
I have out my back right quarter window on 240z. i bought all new weatherstrippings and put them on. Now it is Tight.... i am mean too tight. I have the weatherstripping on right and solidly. However, even with me pushing the window in with everything i have it still will not line up with the holes. I compared the weatherstripping with the OEM on my left side and its definitely thicker. Anyone else run into this issue?
Last reply by crayZlair, -
- 1 reply
- 835 views
@Patcon https://www.youtube.com/watch?v=_u31t13QO6A
Last reply by Patcon,
-
Recently Browsing 0 members
- No registered users viewing this page.
