Electrical
Anything about the electrical system on a Zcar.
3,450 topics in this forum
-
- 1 follower
- 2 replies
- 785 views
I see on other posts, pics where there are big red and big wh/red wires for the headlights. Can anyone tell me where these wires go to. I see on the basic S30 wiring diagram that the blue with wh stripe goes to the wiper. Also the red goes to the washer and the gr/wh goes to the lights. Is that correct ? In the first pic there's a red, gr/wh, gr and 2 blacks. ( 1 black goes to the other side ). In the second pic theres a y/gr, y/bla, r/blu and bla. Any help with where these go ? Dave refurbished the combo switch. If you want a pic of the turn signal side, I can do that. Thank you very much.
Last reply by timsz, -
-
- 1 follower
- 10 replies
- 1k views
looking for advice on how to unseat these connectors from the panel and back out the individual pins
Last reply by anthony_c, -
- 1 follower
- 0 replies
- 1k views
Help, whenever I go around the block with my Z, gauge says I did 10 miles, what could be the problem (1972 240z) Sent from my iPhone using Classic Zcar Club mobile
Last reply by footballnick17, -
- 4 followers
- 6 replies
- 1.7k views
I'm going through the hand-gouging ordeal of replacing two instrument light bulbs, specifically the left-side turn-signal indicator, and the high-beam warning light. A friend has suggested that given the difficulty of access, perhaps I should renew them all (good idea), but with LED rather than incandescent. He feels that LED will last forever, but given that we've had one household LED die on us, I tend to doubt that. Anyone have any experience with LED bulbs in dashboard applications?
Last reply by Richard McDonel, -
- 2 followers
- 4 replies
- 960 views
Hello everyone. I need help with this wire. not sure what where it belongs. ‘73 240z. Thanks
Last reply by krZing, -
- 3 followers
- 5 replies
- 753 views
my early 280z uses the ammeter which I prefer to a voltmeter, anyway the problem is its not center when no current is being drawn. I was wondering if anyone knows off hand if there is a centering adjustment mechanical I would presume.
Last reply by Dave WM, -
Identify relay 1 2
by krZing- 3 followers
- 15 replies
- 1.4k views
Can someone please identify this. I have decided to remove dashboard and I found this relay underneath by the stereo. somehow PO cut the 2 black wires. Thanks
Last reply by Zup, -
- 2 followers
- 21 replies
- 2.2k views
Hello everyone, i have a turn signal problem driving me mad. Only thing left is that it´s the EU spec taillights. Plugs are fitting but no turnsignal. Tested switch, relay, fuse, Harzad switch.... Only that the hazard switch is from another year (other plug in 77 than 75). So far I think its wired in correctly though. So, anybody did a Eu taillight conversion and can explain to me what to change how? thanks a million, Richard
Last reply by Villeman, -
- 1 follower
- 12 replies
- 1.3k views
Hello! I am installing some driving lamps, and I will use a relay. I can wire the relay directly to a switch, but common sense (state laws) tell you that driving lamps are only supposed to come on with the high beams. So I have a 12V feed from the ACC circuit on the fuse panel to the relay, and I wanted to wire the relay's ground to the high-beam (ground) wire so the driving lamps come on with the high beams, because the high beam switch goes to ground, right? Attached is a simple schematic. BTW- It's a 1978, so the High beam wire is a RW wire, according to the FSM I atached a simple diagram
Last reply by gundee, -
- 2 followers
- 8 replies
- 2.4k views
Can someone please identify where to plug this connector labeled LW/R/LR
Last reply by krZing, -
Combo switch 1 2 3
by krZing- 3 followers
- 31 replies
- 2.6k views
Can someone please help me identify where this green and white wire connected to. Not sure why the PO cut this wire. I think it’s for the horn but not sure. Thanks
Last reply by krZing, -
- 1 follower
- 0 replies
- 719 views
-Is the relay panel grounded by it's mount to the inner kick panel? -I am having starting issues, used the hard start relay, been starting fine for 2 days and now just click at the solenoid. -I have a 25amp fuse for the hard start relay and it is blowing them . -Battery is new and 12.7 volts. -This electrical system is killing me. Thanks, 'GI
Last reply by GIchiro,
-
Recently Browsing 0 members
- No registered users viewing this page.