Old For Sale Ads
Forum that contains old classified archives.
1,797 topics in this forum
-
- 1 reply
- 6.1k views
I have two Datsun 240Z's for sale. Both of these cars are five speed cars with the low ratio rear end. The 72 is complete except for a bad gas tank. It runs but the body is rough and the iterior is marginal. The 71 has a good body with fiberglass fenders, quarter panels, and rockers. This car is taken apart for painting and I think it is complete. The 71 did run last year but one of the carbs leaked gas. The 71's interior looks good. Make me on offer. I can deliver if the price is right. I am in central Ohio.
Last reply by Mike, -
-
- 2 replies
- 1.2k views
Project car for sale. Engine apart. FG front fenders and rear quarters. For details call Steve at 941-379-2350. Car in Fair Haven Michigan. Can email photo. $1,000
Last reply by Frank, -
- 0 replies
- 1.4k views
i am selling a one owner 1973 240z. It has fiberglass fenders and 1/4 panels. The motor is done to race but he carbs need to be set. it could use frame rails and patching in the floor. the car is driveable. looking for best offer
Last reply by marc, -
- 0 replies
- 1.1k views
I have searched high and low. I live in BC CAN, and the only place I have found them available is Motorsport Auto in CA, and it will cost a fortune to ship to me. Does anyone know of a supplier in CAN?
Last reply by jaybird, -
- 1 reply
- 2k views
As the subject says, I'm selling the differential I took out of my 1970 Solo 2 BSP Z when I put in the Quaife. Its all setup and ready to bolt in. Lots of preload so it acts as a locked differential under power but freewheels while coasting. $500.00 and you get to pay shipping. I can deliver it pretty much anywhere in Southern California. ------------------ ---------- John Coffey johncof@veriomail.com
Last reply by John Coffey, -
- 5 replies
- 1.7k views
Greetings all! Nice place ya'll got here!...I'm looking for a set of the makuni carbs, either online or other sources that ya'll may know of....I'm not real sure if I posted this in the right place, but appreciate your tolerance of my newby-ness! Best regards...jim
Last reply by Jim Frederick, -
- 0 replies
- 1.3k views
240Z parts car with E31 Head. As far as I know the head has never been cut, the car has 43,000 miles. This car is not restorable, no floors and extensive rust on the frame rails. Extras: Doors, windshield, hood (no paint with surface rust), early SU's, tail lights, 240 and 260 consoles, cowl, door and rear quarter glass, original hubcaps, original steering wheel. The car is located in Staten Island, NYC. I can ship parts. Steve Joseph wardhill@interport.net 718 816-9449
Last reply by Steve Joseph, -
- 4 replies
- 3k views
I have a totally restored 1972 Zcar. Everything stripped down to bare metal and repainted 1972 British racing green. Engine professionaly rebuilt with Nissan parts. Any part which was not in great shape was replaced with new Nissan parts including bumpers, hub caps, door skins, front fenders, front and rear glass, door regulators, virtually everything on the engine, exhaust system (stock), headliner, seats, carpeting, headlamp housings, springs, shocks, michelin tires, etc. I am the original owner and the car sits under its white cover in a heated garage. Call **** Haugan at 206.780.0550 or email. ------------------
Last reply by MB, -
- 4 replies
- 1.3k views
I'm looking for a gas tank(in good shape...obviously!) for my '73z. Not an easy thing to find, it seems. Had one lined up and someone stole it!! Sheeesh!!! FYI,I live in Halifax, Nova Scotia, Canada.(East Coast)
Last reply by Phaedrus, -
- 0 replies
- 1.2k views
For Sale: Mint 1970z Stock except for short throw 5 speed, and wheels. Car is excellent inside and out.No rust! Runs like new. Covered and garaged. Motivated seller going off to school. $5000. Call 561-586-0389 (south Florida) or e-mail. Hurry it won't last!
Last reply by mac240z, -
- 0 replies
- 1.3k views
I need a intake manifold for an L-16 that fits twin SU carbs,or twin sidedraft carbs.
Last reply by DC, -
- 0 replies
- 1.5k views
You will need this head to realize the full potential of your stroked motor. I have several non=hydraulic P-90's $275.00 you pay freight Kansas city location (will crate)
Last reply by DC,
-
Recently Browsing 0 members
- No registered users viewing this page.