Old For Sale Ads
Forum that contains old classified archives.
1,797 topics in this forum
-
- 0 replies
- 1.3k views
Here's what you get: -Complete L28 long block with N42 head, converted to dual carb setup. -round top SU carbs -motorsport 6-2-1 header -FRAM oil filter!!!! -airhorn (not pictured) with a new filter -6 spark plugs -distributor -ignition module if you need it -starter -last but not least, a fully functional dipstick The previous owner said this motor ran fine 8 months ago, so I only have his word to go by. There's rust on the header, but it's only surface rust. A good run with a wire brush will take care of the culprit. update - sold Please email aux@highrpm.org or dsmithgns@attbi.com
Last reply by auxilary, -
-
- 1 reply
- 713 views
I have 4 caps w/the clips still on the back for sale for $35 plus shipping. I have an extra set of 4 that look just like the ones on my current wheels in my photo gallery. Very clean....
Last reply by rudi, -
- 5 replies
- 1.2k views
For sale/ trade 280z gray cloth seats(lever to fold forward) look refurbished, 1 small tear on drivers side seat kidney support, very good condition $200 takes them both 4 14inch centerline autodrags(could be knockoffs...don't have any real centerlines to compare to) I want to trade these for different wheels...14 or 15 with good tires. These aren't my style really. Also, these have very good tires on them and would go with the wheels. r180 3.36 diff in parts, but all there. just have to put the gearing back in the case and bolt on the side flanges. No special tools required. Took about 10 minutes to unbolt the flanges and slide the gearing out so it should take 10 to…
Last reply by drmattyg, -
71 240z seats
by R0N- 2 replies
- 911 views
I have a pair of stock 71 240ZSeats - $40 or best offer. Local sale only. You pick up. Has small ripple rip located on the third picture. Not noticeable because located in left rear of drivers seat. You would not notice it if you were looking through the rear hatch. Thanks for the space classic Zcar -Ron Drivers seat - rear shot Picture of ripple rip at left side of drivers seat
Last reply by R0N, -
- 2 replies
- 957 views
I have a bunch of things for sale also that I would be willing to trade. -L28 engine with some FI equipment. I don't know how it runs, but it has been sitting a while. -$200 -ground control FRONT ONLY coilover springs, seats, and end caps. no camber adjustment stuff on them. -$200 -A set of mags as can be seen on my car in these picts: www.cardomain.com/id/drmattyg the wheels will be off my car shortly -$250 centerline autodrags(trade only) -a set of 73 carbswith linkage and air filter(if you need some little parts) -$50 Here's what I'd trade for: -Tokico or Eibach springs -3.90 r200 in GOOD CONDITION with mustache bar, half shafts, etc -Sparco, Corbeau, or MOMO …
Last reply by SN8BYTE, -
- 11 replies
- 1.4k views
1972 SU 4 Screw Round tops - All that you see in the Pics. $80.00 plus the shipping Jeff Pic 1
Last reply by JEFF, -
- 10 replies
- 1k views
It is necessary for me to free up some space to start up my promotional merchandising business (plug, plug) and consequently I have decided to part out my 1974 2+2. I will be stripping as many of the useable parts as I can this weekend with a view to sending the carcass off to the scrap yard late next week. If anyone is after a particular part please let me know and we can negotiate.
Last reply by Nigel Mulvey, -
- 1 reply
- 811 views
I was thinking about selling my 1970 z. Manufactured in 5/70. t is undercoated, and has almost no rust. It has a carbeurated '75 2.8 liter engine, custom 'z's upholstered in the doors and seats. It runs very strongly, and is very fast. It starts evry time, no problem. Things I have replaced over the last 2 years: 1) Electrical system completely rebuilt by a Z specialy shop 2) New choke cable 3) New license plate lamp 4) New dash cover 5) new gear knob that says '240z; 6) the paint job is about 3 years old I have an original steering wheel that I have not installed. Some minor problems: 1) it uses some oil. 2) a few chipped areas on the paint 3) I have a repl…
Last reply by civ104, -
- 6 replies
- 1.5k views
Hi everyone, I've got a custom fab'ed exhaust system for sale that fits the MSA 3-2 header (#15-6001). You'll note that on that header the final collector is a separate add-on piece, what we did was not use it and simply weld flanges at the end of the 3-2 portion. The exhaust bolts right up to that: so you've got two 2" exhaust tubes that go all the way back to a Magnaflow muffler with two exhaust tips aligned vertically one above the other (for that Japanese "432" Z look). It bolts to all the factory exhaust locations and even has a welded in bung for putting in an O2 sensor to help you tune the carbs. When I had it on my Z I got nothing but compliments about how it s…
Last reply by EricB, -
- 3 replies
- 1.5k views
73 240Z WITH 71 STOCK ENG 86,000 MILES. BODY STRAIGHT WITH MINOR SCRAPS,CHIPS. MINOR SPOTS OF RUST BELOW DOOR AND TRUNK LID. NO RUST INFRAME OR BATT AREA. ORANGE PAINT BLACK INTERIOR. MAG WHEELS OTHERWISE STOCK. RUNS VERY GOOD USES NO OIL. HAS NON OP SINCE 93. HAS AIR COND NEEDS TO BE CHARGED. IN CENTRAL CALIF AREA. CALL 209 6326304 OR E MAIL PTURBOZ@AOL.COM PHIL 2,700.00 ALSO HAVE EXTRA SET OF SLOTTED MAG WHEELS, ORG 73 MOTOR AND 74 260Z FOR PARTS. ALL GOES WITH CAR. I DO NOT HAVE WAY TO SEND PICTURE.
Last reply by thedatsunkid, -
- 0 replies
- 962 views
Original 1979 280 ZXR. I have R- code race wing for vehicle. This ZXR is very restorable. 192K miles looking for person who realize this cars potential. Car is in SoCal. Contact me at; rsp1@earthlink.net
Last reply by Jon D., -
- 15 replies
- 1.5k views
Hi, I'm about to offload a few of my parts I don't need but I have no idea what to sell them for, any suggestions: - 5 speed 240z gearbox - 4 speed 260z (I think) gearbox - 4 speed crash gearbox - Complete L24 engine all in bits, new seals, etc - 240 Break booster - Panels: Front fenders, crowl, front light units, front grill, 1/4 windows and trim, front bumper. Thanks
Last reply by 72zcar,
-
Recently Browsing 0 members
- No registered users viewing this page.