Welcome Guest! Please read more information about our club!

Old For Sale Ads

Forum that contains old classified archives.

Followers 0

1,797 topics in this forum

Sort By

Free 1973 240z

March 21, 2003 by bryantatem
8 replies

1.7k views
This is in San Antonio I have no title Basically it is a naked unibody with suspension and a rear end and half shafts. If no one takes it I am going to cut it up and take it to be recycled. I just need it out of my garage. -Bryan

Last reply by bryantatem, April 2, 2003
L24 Big Block In Oz

April 1, 2003 by nixcars
1 reply

698 views
Bored & stroked to 2.8 litres, fully ballanced & fully reconditioned with flat top pistons, N42 ported head, high volume oil pump, heavy duty valve springs, 38/68 cam, electronic dizzy, RPM heavy duty clutch kit, light flywheel, twin SU's with Pipercross air filter & SWR mandrel bent extractors. Has been fitted to car & just run in. $2900.

Last reply by trs, April 2, 2003
6 into 1 Header anyone?

March 26, 2003 by JEFF
3 replies

852 views
Square port is currantly on the E88 head i took off my car last week - ( installed N47 w/ fuel injection ) I now have a round port head so i don't need this header - It was in use on my car for 2-1/2 years. ************* SOLD ************ Make me your best offer and it's yours!!! ( plus the shipping ) - Jeff

Last reply by phi22b@ck, April 2, 2003
L28 Engine with N42 Head

March 26, 2003 by Dickf
4 replies

2.3k views
L28 Engine with N42 Head. $300.00/Offer. No carburetor, manifolds, starter or alternator. Used engine which was installed and used while my original engine was re-built. Ran good. Approximately 70K. Located on an engine stand in my garage in Sammamish, Washington.

Last reply by Dickf, March 31, 2003
The Ultimute 240z

March 31, 2003 by 70sbeaver
0 replies

1k views
This car is one of only 3 ever built, Dry weight 841 kilo's. Engine Bored out to 2600cc, 7700 rpm, Thriple dellortos 48s, producing 285bhp, oil cooler, high pressure braided hoses (Samco & Nismo) both for water/fuel, lightened fly wheel. Engine fully balanced and blueprinted, steel rods/crank block pressure tested, all parts from Nismo sport in USA. Exhaust manifold 6-1 (Sounds like a Nascar) 95dps/108 without silencer insert. Gearbox AP 3 Plate racing clutch, RS240 ex touring car close ratio gearbox, 9.1 RS 240 diff & cooler, Brakes Front Willwood 6 pot cailpers on 13inch vented AP disc's Rears Wilwood 4 pot cailpers on 10 inch vented AP disc's Adju…

Last reply by 70sbeaver, March 31, 2003
New Rb30 Block In Oz

March 31, 2003 by nixcars
0 replies

1.1k views
From Nissan's old stock pile with crank cradle & bolts, no machine work required, ready to assemble. Ideal for building a DET engine. $500AUS.

Last reply by nixcars, March 31, 2003
help

March 30, 2003 by johnnymo
1 reply

647 views
has anyone ever seen those headlight conversions? do you kno where or if they are even for sale, and where i could pick up a pair? thank you

Last reply by texasz, March 31, 2003
71 240Z Engine

March 30, 2003 by webstes
0 replies

724 views
1971 240Z Engine. I removed it from the car last weekend. The odometer read 76K. The engine turns over. It should be gone through before putting in another car. It is complete, less the carbs and I'm asking $200 for it. I'm located in Northern Connecticut and can be reached at stevewwebstes@aol.com. I would prefer not to ship.

Last reply by webstes, March 30, 2003
who wants to go fast

March 26, 2003 by johnnymo
7 replies

1.5k views
i have a 71 datsun with a worked lt1 pumping out 500+hp to the rear wheels new interior racing seats wheel gages i have a its lowered and its on 18" rims i also have 17" if you would perfer them its a black with semi tints in the back all work has been done in my garage please e-mail me at johnjohnmo@hotmail.com make me a offer

Last reply by Z-point, March 30, 2003
FS: 74.5 260z electronic fuel pump

March 28, 2003 by dogma420
0 replies

787 views
I have an electric fuel pump from Nissan, it was brand new in '92, the car got totalled in the front end in '93, and the fuel pump has just sat. The flex lines were cut, and whole cage is intact with the fuel pump. It is genuine Nissan, and cost approx $300. (don't ask why we didn't get something else). Anyways, I have it for sale, please reply to dogma420@hotmail.com if interested. It came out of a 74.5 260Z, (big bumper edition). I am in Portland, Oregon. Look for my other thread, FS: Electronic Brain Box if you need the box that controls the ignition for the same year car.

Last reply by dogma420, March 28, 2003
'72-'76 Master Cylinder (New Remanufactured)

March 28, 2003 by benn9090
0 replies

981 views
This is a new-in-box remanufactured Tokico 7/8" Master Cylinder fitting any '72-'76 Z car. Compare to part number 24-5081 from Motorsport Auto at $134.46. Unlike cheap rebuilt master cylinders (A1 Cardone, etc.) from discount auto parts stores, this one was rebuilt with ONLY Nissan OEM seals, springs, check valves, and copper washers. Most $40 rebuilt master cylinders are rebuilt with aftermarket seals of poor quality, and the springs, check valves, and copper gaskets are reused. $50 shipped. email: benn9090@midviewinternet.com

Last reply by benn9090, March 28, 2003
NIB Nissan OEM: L28 Int/Exh Manifold Gasket & Studs

March 28, 2003 by benn9090
0 replies

1.1k views
Bought new from Courtesy Nissan last year, don't need anymore. 14 studs and L28 square port gasket, new in Nissan packaging. Courtesy pricing was $9.94 + $28.27 + $10.50 shipping =$48.71 Will sell for $30 shipped. Mail at: benn9090@midviewinternet.com

Last reply by benn9090, March 28, 2003