Interior
Discussions about the interior components of your early Zcar.
2,368 topics in this forum
-
- 2 replies
- 1.6k views
Just won this 240Z euro dash and i feel lucky Chris
Last reply by hls30.com, -
-
- 12 replies
- 3.2k views
Does anyone know the history of these Center Console Arm Rests? Are they after market items? Still available? I am relocating the pad from my 70Z console to the 71 Z console because I really like it and I drive the 71 every day. (Not to mention, the JCCS judge gave me the evil eye on my 70Z indicating it wasn't a stock part). Also saw the pad on this photo, but this pad looks a bit taller and nicer than mine. http://www.classiczcars.com/forums/album.php?albumid=177 Thanks, Rich
Last reply by ZCurves, -
- 5 replies
- 2.1k views
Is there any good place to get or does any one of any one with nice 260z door panels in tan?
Last reply by zKars, -
- 6 replies
- 1.6k views
Ok, I bought a new vinyl panel for the inside of the hatch. It didn't come with any holes in it. The old one was attached via those little plastic pins that are used to attach all the plastic panels. It also had some sort of black sealer around the inside edge, probably to seal out exhaust gas. I like the look without the plastic pins, but that leaves me with using glue, which I'm concerned wouldn't hold. Has anyone had any luck using just glue? If so, what glue did you use? If I have to drill holes in this panel, does anyone have any tips on how to do it without messing up the vinyl? I'm thinking just put a piece of tape over it and drill. The attached pictur…
Last reply by Zs-ondabrain, -
- 7 replies
- 2.7k views
Let me know what you guys think. I was looking around for a good place to mount the two 6 1/2" pioneers I have. I thought this might be a cool place for a speaker box. Its no permanently set where it is in the pictures Im just getting an idea of the look. Any feedback would be appreciated. Thanks alot guys! -Johnny
Last reply by ConchZ, -
- 3 replies
- 1.7k views
anyone seen this before? I can't quite tell from the description if its the same old plastic dash cap, or if its actually covered with some soft vinyl. Interesting add, at least.
Last reply by hls30.com, -
- 6 replies
- 2k views
Does anyone know if this little vinyl boot is still available? It's the one that conceals the wires coming out for the console and going up into the dashboard. Mine has overspray on it and it would be nice to have a new one.
Last reply by LBO730, -
- 5 replies
- 1.4k views
Does anyone have an idea where to buy a rear view mirror - the complete assy that plugs into the fitting at the sun visor clips? No luck on internet searches thanks Davis
Last reply by esprist, -
- 6 replies
- 4.4k views
I have a 1971 ashtray in need of repair. The plastic shoulder that the left hinge pin is screwed into has broken and been lost along with the hinge pin. Does anyone have a hinge pin for sale or know where to get one? Secondly, has anyone had luck rebuilding lost or broken plastic parts? The ashtray is in presentable shape otherwise...
Last reply by kunzma, -
- 1 reply
- 1.6k views
I just wanted to show you this cool conversion to make a series 2 steering wheel look like series 1 steering wheel. (Picture shown is JDM Series 2 steering wheel) You cut a piece off an aluminum panel in a shape of the slots, and then fit it right in without using any glue. Make sure it is tight fit. This conversion is still in process by a shop in Torrance,CA, since this is kind'a killing free time project.......If you pay someone to do it, it would be cheaper to buy a real Series 1 steering wheel after all. Oh, well....... (Courtesy of M. Matsuoka at M's Factory in Torrance, CA ) Esprist www.jdm-car-parts.com
Last reply by psdenno, -
- 14 replies
- 9.7k views
Getting ready to replace the door plastic liner and need recommendations. Do I go with the MSA replacement plastic or a Dynamat sheet instead? Thanks.
Last reply by dk240z, -
- 0 replies
- 1k views
A couple of years ago there was a discussion concerning stress relief drilling of dash cracks here: http://www.classiczcars.com/forums/showthread.php?t=22361&highlight=dash+crack+drill (didn't want to awaken the sleeping old thread controversy) I just dropped my dash off in Tucson to be refurbed and have a small crack repaired and had a moment of clarity and remembered to ask the guy if that would work and he said that was exactly what he was going to do to stop it from going further. He said there was a slight chance it might resume in another directon but this would stop the current crack from further progress. Thought someone might need to know.
Last reply by vercingetorix,
-
Recently Browsing 0 members
- No registered users viewing this page.
jfa.series1
