Interior
Discussions about the interior components of your early Zcar.
2,368 topics in this forum
-
- 3 followers
- 17 replies
- 16k views
Does someone knows if there is a power antenna in the market that is close to the original ? I've seen that HARADA is claiming that it does. I would like an antenna that operates the same way, e.g. the switch on the radio activate it up and down instead of automatic up and down when activating the radio.
Last reply by scotta, -
-
- 9 followers
- 77 replies
- 20.4k views
How many different seat types came in the early Zs? Mine is a 1970 ( Nov 1969 production ) RHD Fairlady. My problem is the right seat was replaced at one time because it was torn :mad: The replacment seat has a different design around the head rest. Does anyone know what year seats would be correct?
Last reply by nix240z, -
window issue 1 2
by arcdef- 4 followers
- 21 replies
- 2k views
Hi All,I am hoping for some help/advice on an issue with my 260Z's window. Since buying the drivers side window was quite stiff to wind up/down but i thought it was just because of its age. The other day however as winding up there was a loud 'pop' at which point the window dropped and had come off of its guides.I took the window and regulator out, cleaned and re-greased and reassembled however it is now just as stiff and wont go all the way up as seems misaligned. I have attempted to adjust it using the front sash and rear guide however can not get it to sit right.I am starting to think the regulator itself may be damaged as it appear to be fouling on itself.Does anyone …
Last reply by Freez74, -
- 10 followers
- 18 replies
- 3.2k views
Guys, my car is in the process of getting most of the interior parts reinstalled in the vehicle. When i purchased it, the interior was basically stripped and i have been piecing it back together. MY question is which piece should i have in the location directly in front of the shiftier. is it this? or this? or this one? i believe it is the first pic because i do not have a series one car. Vin pick below:
Last reply by Mike, -
- 1 follower
- 11 replies
- 1.8k views
Hi, I'm trying my hand at restoring a steering wheel and can't determine the function of this metal ring. It is a little rusty but I can't seem to remove it (that woild be nice) but if it doesnt matter I will leave it as is. --Thomas
Last reply by zKars, -
- 1 follower
- 1 reply
- 767 views
Several months ago, I ran across cardboard (?) caps that fit over the rear strut towers. They fit under the diamond vinyl. The intent was to form a flat surface for the diamond vinyl to lay on. They came that way from the factory. I have an earlier car that didn't come with those but I was positive that I saw them at a zcar parts store somewhere. I am sure I saw them but I cannot find them anywhere. Does anyone know where they can be bought? I would like to avoid trying to make something. I suspect the vinyl install wont look good when I am finished based on how I have seen the other results. So the less variables I can introduce, the better I should be. Tha…
Last reply by zKars, -
- 2 followers
- 4 replies
- 1.4k views
Wondering if i can fix this small crack without pulling it from the chassis. Anyone?
Last reply by siteunseen, -
- 4 followers
- 16 replies
- 2.9k views
Im tired of seeing the horn button fall from the wheel. Any solution for this other than buying a new one?
Last reply by Dave WM, -
- 1 follower
- 2 replies
- 836 views
Howdy, I wanted to clean up this old vent before installing it, I’m a little concerned about damaging the chrome on it, wanted to know if anyone had advise about this, don’t want to ruin/damage it. regards
Last reply by 26th-Z, -
- 5 followers
- 14 replies
- 2.8k views
My driver's side door handle is pulling loose from the door. The metal plate embedded in the handle and used to connect it to the door panel is starting to pull away from body of the vinyl handle. Does anyone know how to repair this problem? I have some handles that I can practice on, but I don't know how I should approach it. -Dann
Last reply by Mike, -
- 1 follower
- 4 replies
- 1.2k views
I have an MSA carpet in the hatch area. The back edge is up against the two rear luggage strap mounts, and this forces the carpet forward, leaving a bulge in the middle. The carpet is too long. Should there be, or should I cut notches in the rear edge of the carpet to make room for the mounts, or should I punch through the carpet and screw the mounts down on top of the carpet? Thanks
Last reply by Richard McDonel, -
- 1 follower
- 0 replies
- 1.1k views
I have a late year 260 and I'm changing the interior from tan to black. I found a guy a few hours from me with door panels; all the plastic trim; and the vinyl out of an early year 260. Will i be able to use the door panels and the plastics? I heard the rear shock towers were taller in the late year cars and that seems like it would affect the trim and maybe the vinyl. Any help is appreciated!
Last reply by Jeff260Z,
-
Recently Browsing 0 members
- No registered users viewing this page.
Seppi72
