Interior
Discussions about the interior components of your early Zcar.
2,368 topics in this forum
-
- 1 follower
- 1 reply
- 3.4k views
When Black Dragon was liquidating their parts a few years back, one of the (many) things I bought were replacement rubber pedal pads for my '78. The clutch and brake pedal pads seem to fit fine, but the gas pedal pad keeps coming off. The rubber is thinner than the original one and allows it to slip off from where it wraps around the back. I tried some 3M spray adhesive with poor results. Would weatherstripping adhesive be the best way to get it to stay?
Last reply by zKars, -
-
- 1 follower
- 1 reply
- 1.2k views
Does anyone know how I could get Amco floor mats for my Z?
Last reply by jonathanrussell, -
- 2 followers
- 6 replies
- 1.6k views
Hi guys, I am assembling the seat belts and noticed the belt that fastened to the top seems to be missing something. To me if I tighten the bolt down it is just going to crush the plastic. Am I missing something? Sent from my iPhone using Classic Zcar Club mobile
Last reply by joe newsom, -
- 3 followers
- 3 replies
- 853 views
This sounds like a stupid question to write, however I am puzzled. Any idea where the jack location goes? Sent from my iPhone using Classic Zcar Club mobile
Last reply by joe newsom, -
- 2 followers
- 2 replies
- 826 views
Anyone know the screw size and where to buy one. Mine is broke off. So I am planning on drilling it and replacing. Sent from my iPhone using Classic Zcar Club mobile
Last reply by joe newsom, -
- 2 followers
- 20 replies
- 4.1k views
Jai (Redwing) found a spring in the drivers side foot well. Looking at the pic she sent it appears to be either the clutch or brake pedal return spring. My guess is clutch spring. A couple of questions. Are the clutch and brake springs interchangeable? I have a good brake spring and the nylon? spring perch from a late 71. Will the late 71 spring work on an early 76 280? Thanks.
Last reply by SoCalJim, -
- 5 followers
- 14 replies
- 1.6k views
I have a broken window roller on the driver's side door. Is this thing repairable (and how?) or should I look for a used replacement? Thanks!
Last reply by zclocks, -
- 4 followers
- 5 replies
- 1.3k views
Anyone know how to replace the felt strips with staples? Or are more commonly glued on? Sent from my iPhone using Classic Zcar Club mobile
Last reply by 52crankman, -
- 3 followers
- 3 replies
- 1.3k views
Anyone know where to source the felt (weather whisker strip) at the top of the door panel for a 1972 240Z?
Last reply by joe newsom, -
- 1 follower
- 5 replies
- 944 views
Found battery totally dead. Maybe the interior dome light was bumped on while getting stuff from hatch area. Need to check it first before testing anything else. Doubt if I can remove the plastic lens without accidentally turning it off or on. Thinking check continuity at fuse box if it has it's own fuse. Also want to find an LED bulb for it that won't use as much power next time it's left on. Until then I plan to remove that bulb whether or not it was the problem this time, since it's killed the battery before.
Last reply by siteunseen, -
- 2 followers
- 8 replies
- 3.2k views
I'm thinking about changing the interior vinyl and panel colour from Off White to Black, the door panels will pose the biggest headache but I was wondering about the "basket weave" on the 77 seats, is it fabric or cross hatched vinyl? Could I use all vinyl seat covers from an earlier year or are the 77 seats so different they need a specific covers? The car came with a fabric insert in the seat covers but I'm not sure if it is stock or aftermarket, Thanks
Last reply by grannyknot, -
- 9 followers
- 27 replies
- 4.7k views
There have been several posts on how to - and how not to - install the headliner in 240s etc (tricky job). In comments there seemed to be some confusion over which adhesive was most effective. 3M Super 77 was suggested by some, and denigrated by others. I called the 3M factory, and they replied by e-mail, and flat-out said that Super 77 is "not strong enough," and further that it will deteriorate anything with foam. They recommend 3M part number 08088 "Spray Trim Adhesive." This is considered an industrial rather than an automotive product, so your local auto supply shop will likely not have it - you have to go to an industrial supplier. Looking forward to get…
Last reply by Car54280ZX,
-
Recently Browsing 0 members
- No registered users viewing this page.
Yarb
