Interior
Discussions about the interior components of your early Zcar.
2,368 topics in this forum
-
- 4 followers
- 18 replies
- 2.9k views
My JVC CD receiver shorted out over the winter when the heavy winter dews got inside- I should've brought it in the house for storage. So I went to BestBuy to see what's available, and the current CD receivers basic are of two types- Bluetooth and "Media." The bluetooth ones connect to your "phone" which I don't have, so it won't help me. I do have a tablet for navigation, and if I could feed the audio instructions from the tablet to the receiver while driving, that would help. The "Media" units have one or two USB ports where you connect flashdrive, or an Android or IOS device for access to the music on the device, or to control (?) the receiver. Most uni…
Last reply by ramsesosirus, -
-
- 3 followers
- 14 replies
- 2.4k views
Was curious if I am using a odometer from a donor car should I use mileage on that or should I reset if that is possible? Sent from my iPhone using Classic Zcar Club mobile
Last reply by grannyknot, -
I believe both of the seats of my car have been misplaced. One should be on the passenger side and the other on the driver´s side. I did noticed that only the right one (passenger side) is the only one that has a cable underneath. Shouldnt this cushion be on the driver´s side?
Last reply by jalexquijano, -
-
Dash cracks 1 2
by joe newsom- 8 followers
- 20 replies
- 5k views
Question for you guys. I have two cracks about 5 inches long. In your opinion is it worth trying to fix? Do those covers look good? What are the fix options? Sent from my iPhone using Classic Zcar Club mobile
Last reply by Captain Obvious, -
- 2 followers
- 7 replies
- 1.6k views
I've been reading through some of the great seat rebuild threads and have been wondering how firm are the new molded foam inserts from MSA and other venders? I love the look of the OEM seats but mine are mush, I'd rather rebuild them then go aftermarket as long as the outcome is a nice firm seat. Could someone who has done a rebuild comment on how much of a change the new foam makes? Thanks, Steve
Last reply by uk66fastback, -
- 4 followers
- 6 replies
- 1.4k views
I'm replacing the crappy Victoria British/Black Dragon straps that I installed in the early 90's and have had a couple of the clips that hook into the seat frame holding the straps in place break on me. Rather than see how many more break I'd rather just replace them all with new. I am able to make my own as it's pretty easy to fabricate a jig to bend the wire I would honestly rather just buy them if possible. I've check some upholstery supply stores online but have found nothing so far.
Last reply by jwtaylor, -
- 2 replies
- 938 views
Just found that the screws that fasten to the steering tube were worn and replaced them with allen type screws. Aint this better?
Last reply by jalexquijano, -
- 1 follower
- 1 reply
- 3.5k views
I need help in finding the best supplier to match the seats in my 77 280z. As you can see in the top picture the covers I have are way off. I need something like the lower picture.
Last reply by gwri8, -
- 2 followers
- 6 replies
- 2.7k views
Do the 72 - 78 seats match up to 70 seat to bolt them to the floor? I like the spring seat bottom and recline adjustment much better on the 72 - 78 seats.
Last reply by JSM, -
- 4 followers
- 39 replies
- 24.1k views
After much searching, I found an overseas source for an S30 leather dash cover made from Italian leather. Finally got it delivered yesterday and will document the installation process here for those interested. I had previously attempted a dash repair with SEMS bumper repair but found problems with thermal expansion/contraction causing failures at the vinyl joints. The advantage of leather is the material will expand and contract with the material underneath without failing. Since this vendor is new to me, I won't give the source until I determine the quality of the fit and difficulty in installation. I am also working with them to verify their design. So far…
Last reply by emrik, -
- 0 replies
- 881 views
I have Corbeau brackets and seats . How do the brackets attach to car ? Do you put the bracket on the seat before putting in car? Do you just attach the 1 part of the bracket to the seat before putting in car? Bracket has 2 parts. Any help? Thank you.
Last reply by timsz, -
- 1 follower
- 2 replies
- 1.1k views
Do the 2 bolt holes go towards the front of car or the 1 hole ? Thanks
Last reply by 7tooZ,
-
Recently Browsing 0 members
- No registered users viewing this page.
jfa.series1
