Interior
Discussions about the interior components of your early Zcar.
2,368 topics in this forum
-
- 2 followers
- 8 replies
- 1.4k views
I'm considering these for my Z: https://www.interior-innovations.com/index.php/welcome/product_detail/187 I ordered the seat covers and shift boot from them and am very happy with the quality, so I assume the door panels would be equally good. The price definitely is. Before ordering, some questions: Has anyone ordered a set and can comment on them? They're titled as 260Z, but should fit a 280, right? I got white stitching on my seat covers. I'm thinking about having matching stitching on the door panels but can't make a decision on what to do. (Maybe just around in the center panel and not on the diagonal slats?) This one's a matter of taste, but…
Last reply by cbuczesk, -
-
- 3 followers
- 23 replies
- 5k views
Has anyone used these or know anything about them? http://www.ebay.com/itm/BLACK-LEATHER-2X-DOOR-CARD-LEATHER-SKIN-COVER-FITS-DATSUN-240Z-260Z-280Z-/231398294528?hash=item35e069c400&vxp=mtr Considering the price of new door cards or even vinyl skins these look like a bargain.
Last reply by grannyknot, -
- 1 follower
- 13 replies
- 2.2k views
So I have this weird toggle looking switch on my center console and I have no clue what it does. It's in between my fasten seat belts and rear defogger emblems. Wondering if anyone knows what it is for/ what it does?
Last reply by Mike W, -
- 1 follower
- 11 replies
- 2.1k views
missing some pieces for the vinyl interior. wasn't too happy with the strut tower and wheel well piece fitment, though i'm not sure where they came from. looking to get the side-sills and pillar and roof side and front pieces (with foam if it's available, or else I'll have to track it down). was thinking of classic datsun motorsport pieces unless there are better repros that are closer to 1970 ones?
Last reply by Careless, -
- 6 followers
- 26 replies
- 3.9k views
Has anyone purchased the door panel vinyl skins from "Z Car Source". I believe they are $145, not bad price.
Last reply by jalexquijano, -
- 2 replies
- 1.3k views
i am looking for a kit that replaces the vinyl with carpet, in black, cut pile. so far, not much luck. this one on ebay looks fairly nice, but doesnt look to include the rear shock covers or wheel well pieces. anyone tried it? http://www.ebay.com/itm/REPLACEMENT-CARPET-KIT-FOR-1971-1974-DATSUN-240Z-260Z-BLACK-CUT-PILE-/400720872442?fits=Model%3A240Z&hash=item5d4cd343fa:g:aUQAAMXQ-KRRikhD&vxp=mtr thanks all sb
Last reply by bonsi, -
Both of the original seatbelts on my 240z are worn meaning they do not retract. Besides of that i will need to send them for full restoration as the screw that attaches the shoulder and lap does not keep in place. Any recommendation for high quality replacement for both of them?
Last reply by jalexquijano, -
- 4 replies
- 1.1k views
Ebay ad says 280z but clearly these are 280zx seats. Will these fit my 77 280z without major work? Has anyone done this swap before? For some reason I like them.
Last reply by rcb280z, -
- 2 followers
- 4 replies
- 1.5k views
I'm am going to rewrap my door panels and am looking for a new custom look. Anyone that has custom door panels, could you send some pictures over?
Last reply by TheErictag, -
- 2 followers
- 11 replies
- 2.5k views
Here are some pictures showing my steering wheel makeover for my '72. I wanted something a little different but still keeping some tie in to the original rather than go aftermarket. The first picture shows what it looked like when I bought the car. Covered in some weird wrap and lots of rust. I wanted the redone wheel to be thicker so I wrapped two layers of felt around the original wheel to make it about 1/4" bigger in diameter. Finally, I wanted it wrapped in leather. I considered Wheelskins, but I wanted the outer part of the spoke to be covered as well. It…
Last reply by Zedyone_kenobi, -
- 1 follower
- 3 replies
- 1.4k views
My question is can you swap a 280zx clock (or any of the trio gauges) into a 280z? I have done a bit of searching and can't find a write up where someone has put the ZX gauges into the s30. Do they use the same connectors?
Last reply by EuroDat, -
- 2 replies
- 1.1k views
I'm finally getting to put my Z back together after a few years(260 stockish) The seats were recovered 3 years ago and I am just getting back to reassembling them. I noticed that the seat backs have flush bolt holes on one side and protruding bolt holes on the other, other than that they appear symmetric. My thought is that the protruding holes go on the mechanism side and the flush holes go on the spring side. Can anybody confirm or deny they proper seat assembly?
Last reply by GGRIII,
-
Recently Browsing 0 members
- No registered users viewing this page.
Patcon
