Old Want Ads
Old ads for wanted items.
880 topics in this forum
-
- 0 replies
- 842 views
Looking for one of these from a 200SXT. Anyone have one laying around? Willing to spend $200. I have an LSD carrier, looking to swap over. Ring gear bolt size is not an issue.
Last reply by jmortensen, -
-
- 1 reply
- 1k views
my Z needs to have its right steering knuckle replaced. steering knuckles are hard to locate and all of the parts suppliers (contacted so far) can only say, "sorry!" anybody have a right steering knuckle for a '76 280Z available? thanks for your attention. L
Last reply by Z 4 Z, -
- 8 replies
- 1.4k views
Yes, dont laugh, I know its a pipe dream, but I am looking for a set of 4 or even just ONE Works racing wheel like the ones used in japan or on the safari cars back in the 70's, anybody have any leads?
Last reply by somecreep, -
- 0 replies
- 812 views
I need the following to be sent to the UK for my Series 1: Outside hardware for electric antenna; 3x spare tire cover stoppers; tire stopper rubber belt; jack belt. I'll keep asking until I get 'em ! Thanks all, Dave
Last reply by DJACEY(UK), -
- 9 replies
- 1.3k views
hey guys does any one have a set of fender mirrors just lying about preferably in reasonable condition and must be complete prepared to pay what there worth:stupid: for good ones
Last reply by winquist, -
- 4 replies
- 923 views
i am looking for a z to do a v-8 swap, 240, 280 or zx dosent really matter. just want a car with out a drive train in it and a decent body so i dont have to spend a ton on body work i am located in denver colorado
Last reply by madzdriver, -
- 0 replies
- 760 views
I am looking for a hood and fender for my 1971 240, hopefully or near the portland area... passenger side fender by the way. Also, looking for the hard to find front bumper for the car. It's time to put 'er back together and get it on the road for summer dang it! Let me know, you can e-mail me at Brian.W.leclair@bankofamerica.com or call my cell at 503-544-1901. Have a great day! ~Brian
Last reply by justaZcarguy, -
- 14 replies
- 3.5k views
Hi, Just curious if any of you non-North American types that got the 240Z with a factory five speed had a spare shift knob for sale? In the U.S. we got the wooden (walnut I guess) shift knobs with the 4 speed pattern as the 4 speed was all that was available here. Since I've swapped in a 5 speed from a later model I'd like the 5 speed wooden knob (not the fake leather one). If you have a decent spare, would you be willing to sell it to a Yank? Or, If you have an extra (uncracked) plastic disk with the shift patter (black background, white pattern), I could just put it on my four speed knob in the place of my original disk. I guess I'm assuming the 5 speed knobs in …
Last reply by Go240Zags, -
- 0 replies
- 764 views
I am looking for screws that hold the Heater control/radio panel in place on my 1971 240Z. They have a dark brown/black translucent finish. The silver ones I obtained from my local Nissan dealer do not look quite right. There are only 4 of them. Also am looking for the embellisher/black trim panel which goes around the taillights and under the license plate. Or is there someway to refinish the one I have? Thank you!
Last reply by Lyle Nelson, -
- 1 reply
- 830 views
A 260 z is also oh k, i need a car with very little rust.
Last reply by texasz, -
- 0 replies
- 807 views
Hey, I'm looking for two (2) Purple aluminum Nismo Valve spring retainers. Nismo #99996M1150. (Bought 10 on ebay) Thanks, ecp48
Last reply by ecp48, -
- 2 replies
- 986 views
I am looking for a cylinder head for my NA L26. Got the bad news yesterday that mine was warped. I would prefer one in N. Calif so I could pick it up and save on shipping. Please let me know. Thanks. Skip
Last reply by agpawa,
-
Recently Browsing 0 members
- No registered users viewing this page.
