Old Want Ads
Old ads for wanted items.
880 topics in this forum
-
- 0 replies
- 1.6k views
hi im looking for triple weber or mikuni carbs for sale. i have a 79 L28 on stock SU carbs. im located in So. Cal LA. e-mail Yuji@iloveracing.com. let me know! thanks!
Last reply by itazura, -
-
260z Badges
by Kirby- 5 replies
- 1.5k views
I am after some badges for the 260z (2-seater). "DATSUN" Bonnet Badge "260Z" Skirt/Fender Emblems "Datsun 260z" Rear Hatch Emblem If you have any of these lying around or on a wreck, let me know and what kind of price you are looking for and we'll try and sort something out. Thanks, Kirby
Last reply by thunderz, -
- 2 replies
- 1.1k views
Anyone have a mustache bar laying around? I would like to drop in my R180 LSD this weekend, and trying to source this part this week. Let me know how much you want for it? Am in Bay Area, CA. Thanks, Brandon
Last reply by byunique, -
- 0 replies
- 1k views
Looking for shoulder belts for a 72. I'm not sure what other years are compatable, but I need at least one belt. Mine are the type that join together with the lap belt and then clip into the female latch. email me if you have what I'm looking for. cbarnett@ago.state.al.us thanks
Last reply by hcb240z, -
- 5 replies
- 2.7k views
All, Looking to replace my driveshaft u-joints preferrably with aftermarket. They are back-ordered at MSA till the 26th, which isn't that long, but would prefer to finish up the job this coming weekend... Any ideas on other sources for Spicer u-joints for a 240Z driveshaft? Manufactures part number would be ideal as well. Are the stock u-joints just as good for a stock engine? Thanks, Greg
Last reply by 240 in OZ, -
- 2 replies
- 1.4k views
Well, its a long shot, but I thought I would ask. I am looking for a shift lever kit that allows you to put a 5spd trans into an early 70/71 240Z without having to cut the tunnel or console. The Nissan P/N is 99996-E3030. If you have this part and would like to sell it, send me a PM. Thanks, Marty
Last reply by Marty Rogan, -
- 6 replies
- 1.5k views
Hi friendz It spring, I hope you are getting ready to roll Z car. By the way. I am looking for this floor mat. Let me know If you don't mind to sell or anywhere I can get. Thanks
Last reply by DatsunZGuy, -
- 0 replies
- 1.1k views
I need a trubo motor and 5 speed tranny. Im also going to need all the crap that goes with em to do a basic swap. The rings in my current stock 73 have had it and im going to have to do a swap sooner than i wanted to so keep your eyes open for me orsell me yours!!!! Thx
Last reply by Dead Roman, -
- 3 replies
- 1.3k views
What's up guys, i just picked up a 71' 240z shell and i grinded all the rust off, i'm not looking for pretty much anything that deals with the interior. Dash, door panel, center console, etc. Leave me a message and a price. Thanks
Last reply by Bambikiller240, -
- 3 replies
- 1.3k views
Hello, I need a driver's side outer chrome door handle. This is for a 1971 series one. I also need a passenger and driver side mirrors. Thanks a lot, savannahz
Last reply by hls30.com, -
- 7 replies
- 2.1k views
Even though it's nice to have fresh plating on my parts I'm a little pissed that the platers lost a small retaining spring for my carbs. Not exactly sure what it's called but, it sits at the end of the circled bolt in the attached picture, between the washer and the bracket. There are 3 springs that go on this bolt. One big one at the base next to the body, another one in between the two brackets and the one that I need at the end of the bolt. It's a flat spring with only 2 "coils". Does anyone have one? Thanks.
Last reply by AxtellZ, -
- 0 replies
- 892 views
Turbo engine found
Last reply by 240Zdragon72,
-
Recently Browsing 0 members
- No registered users viewing this page.
zKars
