Old Want Ads
Old ads for wanted items.
880 topics in this forum
-
- 4 replies
- 847 views
hey im looking for a early 240z shell. i would rather it be in north california. thanks, Julius
Last reply by mandtw, -
-
I am thinking of trying a set of SU's again. I get really bad mileage, maybe 12 - 14 mpg.. It could be just more jetting is needed, or my foot is too heavy,,Don't get me wrong, the car juns fine. But if someone has a full setup from the head out, that they would like to sell cheap. I would be interested..
Last reply by mandtw, -
- 6 replies
- 1.6k views
I am looking for a 4 barrel conversion kit for my 1974 260Z Any help would be appreciated. You can reach me at cooldad16@aol.com thanks
Last reply by zaddict, -
- 4 replies
- 790 views
Hello, here's the problem I need a 240 Door (Passenger side), and in must be cheapish/reasonably priced, I'm more than willing, to get one with rust along the bottom etc, as i can fix it, but not a total write off. If its cheap enough, freight wouldn't be a problem, but on a student's budget, everything's diffiult.
Last reply by Z Kid, -
- 8 replies
- 876 views
Hello all. I am looking for the two "chrome" dohickies that cover the mounting screws for the grip on the right door on a '72. They seem to be in scarce supply. I tried All Z East in Portland and while they have many Z's, there were none of these. I think they break easily. Thanks
Last reply by ZwolleY, -
- 1 reply
- 820 views
Im Lookin For a 1970-1978 V8z in the Colorado Area Would be better thanks
Last reply by Jimz, -
- 2 replies
- 1.3k views
I need a wiper motor for my 240z. It's no longer available from Nissan and I've checked everywhere including Courtesy in TX and Motorsport in CA. Will also consider rebuild if you have any ideas on sources. Thanks, J.Z.
Last reply by ajstonick, -
- 0 replies
- 685 views
I`m looking for a performance engine/head combo....L-28 block thats has a stroker or has a performance package,for my `80ZX don`t need trans..just engine....plus looking for a used JCR supercharger kit that someone is willing to sell or has one sitting around that their not using no longer....e-mail replys to davidjay69@hotmail.com thanks,davidjay69
Last reply by zxjuiced, -
- 0 replies
- 598 views
i am getting my license in march and have always wanted a datsun z. i need a 70-78 240,260,280 z. only have about 1,000 now but should have more by march. want the z to be in good sape and in the midatlantic area of the us near virginia.
Last reply by will_sphyrna, -
- 0 replies
- 819 views
i remember seeing on strictlyz? or shome? or one of those websites a CNC adapter someone had made which sold for $50, was intended for our 240's and allowed the bolt-on use of 280ZX to '84 300ZX rear calipers and discs. I just spent an hour looking for them and now can't find them..... I've found adapters for 240SX rear calipers with maxima rotors, i found kits which required an adjustable proportioning valve, but not what i remember seeing on the 'net like 6 months ago.... does anyone know where i can find what i am looking for? or am i going about it the wrong way and should instead opt for one of the kits i've listed above.... (interestingly none of the kits mention an…
Last reply by EricB, -
- 1 reply
- 1.1k views
I just bought a '72 240Z. It's in great shape except for a smashed quarter panel on the driver's side. I'm hoping to find a new OEM quarter panel for replacement. Am I dreaming in wanting to find one of these? If that's not possible, any suggestions on good sources to check to find a full quarter panel in good shape would be greatly appreciated. Thanks in advance! Jim p.s.: I'm located in the US.
Last reply by 2ManyZs, -
- 2 replies
- 933 views
MSA says that all the early models, up to, and including the black '78 ones, are out of production! Unfortunately, my original '71 wiper arms have finally 'sprung' out. Anyone have a new set they can part with, or maybe another resource?? scott H2O-Z
Last reply by 2ManyZs,
-
Recently Browsing 0 members
- No registered users viewing this page.
jfa.series1
