Old Want Ads
Old ads for wanted items.
880 topics in this forum
-
- 0 replies
- 585 views
I am new to this, so here goes: I am in need of a clutch slave cylinder (complete) for a 4 speed manual (70-74). I am also looking for information on how to replace the rear taillight clusters on a '73 240Z. One of mine is broken and the other near the exhaust is extremely dirty on the inside. If anyone can help, shoot me an E-mail at eftusk@juno.com or jwofford@dstcontrols.com Thanks...
Last reply by Eftusk, -
-
- 0 replies
- 744 views
Does anyone have a Bob Sharp valve cover --- or know someone that does I have been seaching for months I found one but the price is outrageous I would be willing to pay $200 - $300 thought I would make one last ditch effort to find an affordable BSR valve cover (I have an old bsr gt-33 that is missing the valve cover ---I assume a former owner kept it as a souvenir)
Last reply by okdan, -
- 5 replies
- 856 views
I have seen pics of original 240's with what looks like a small rubber air dam on them. I like the look of these but can't seem to find one anywhere. Anybody have any hints? It 's a small air dam that seems to mount to the back of the valance. -Dale-
Last reply by Ron Carter, -
- 5 replies
- 1.2k views
Well.. I'm in the middle of building up the '79 ZX as a good daily driver that can still kick arse and run 12's but.. I want to keep my eye out for a 240, and I have been. Okay, here's the run down I want a rust free project 240, preferably 70-72, but hey, I'd still consider a '73. No floor-pan or rail rust (or, VERY very minimal surface), I don't mind some on body, that's part of the fun of restoring. Anyway, I've found a few in the SoCal area, but most aren't driveable up here to SW Washington where I live, and if they are they are too expensive for me. What I have planned is a 350 swap, plain and simple. I'm not looking to spend more than $1500.. but that's ne…
Last reply by Mike, -
- 1 reply
- 688 views
I have a 70 240z that has riveted body side molding that I want to remove. Any idea of how to remove this without damaging the body in the process. Thanks Mark
Last reply by Mike, -
- 2 replies
- 846 views
I am looking for a complete new rear bumper and bumper guards for a front bumper for my '70. Rechromed would be ok too. IF anyone has one that they want to get rid of at a decent price, let me know. Thanks, Marty
Last reply by Marty Rogan, -
- 0 replies
- 641 views
Is there anyone here located in Aus/NZ, or Europe, or even Japan that might have access to a km/h speedo for a '73 240? Thanks, -e
Last reply by EricB, -
- 4 replies
- 933 views
Both sides, in good condition of course - especially seat bottoms, as I have already rescued two good condition black vinyl seat backs from the junkyard. If I can find these OEM seats then I will have two old Recaros to give away to whomever wants... they are black velour, have adjustable thigh support on driver side, look like the old LX models if you remember that far back, and yes the black velour fabric is torn in places but the foam is intact... Comfortable enough - just not the OEM look that I am after. Thanks. -e
Last reply by Daniel, -
- 2 replies
- 809 views
I need some parts for my Z. Center Console fuse box cover interior trim dash knobs michael@insolwwb.net
Last reply by michael20, -
- 0 replies
- 806 views
Just need the R&P unless you don't want to spend the time removing it from the housing.
Last reply by John Coffey, -
- 5 replies
- 875 views
Need 240 wood steering wheel...good or restorable... Bill
Last reply by Dan Reed, -
- 0 replies
- 1.1k views
I need 6 36mm chokes for my DCOE 40's. I also have 30mm and 33mm that I no longer need and a BUNCH of jets... trade? Frank 408 314-4451
Last reply by L24ITS,
-
Recently Browsing 0 members
- No registered users viewing this page.
Yarb
