Open Chit Chat
This area is for holding open discussions.
5,990 topics in this forum
-
- 1 reply
- 913 views
check it out... more than just the usual suspects... http://www.flickr.com/groups/japaneseclassiccars/pool/ -e
Last reply by Alfadog, -
-
- 7 replies
- 1.3k views
I was wondering how much are these winndsheilds worth if you can find them new or in good condition used..
Last reply by daddz, -
- 2 replies
- 1.3k views
Tomorrow morning we're off to Brisbane for about a week. See ya when I get back. Rick. :devious: :devious:
Last reply by theianmonster, -
- 27 replies
- 4.5k views
Today I measured an engine (4 cylinder) with no load. RPM accelerates at approx 4.6 RPM per 1mS, When accelerating the engine between 3400 rpm 5200 rpm it does it in 389ms. Does anyone know how good or bad this is ? Does anyone know how to work out the "1/2MV2 Theory"? ..
Last reply by smokingwheels, -
- 4 replies
- 1.7k views
Check it out.... 260Z Looks to be in decent shape. If I had garage space it would be mine!
Last reply by moonpup, -
- 5 replies
- 2.3k views
I have an extra copy of "Monumental Senna" by Bernard Asset. 1994 book was sold in limited numbers worldwide (500) and is quite hard to find. 300 pages & sold for $300 new. Book is tough to get and valued up to $1000 by some collectors. I'll sell my extra copy for $525 OBO shipped in the US. It is ultimate Senna photo book with pics from numerous 20+ famous motor racing photographers. PM or email if interested. Thanks! mark.boudoucies@dayzim.com
Last reply by jmark, -
- 3 replies
- 1.2k views
I have a couple of 2007 510 calenders put out by The Dime Quarterly since 2 of my SCCA 510 Runoffs pics made the calender. I'll sell them for $22.00 shipped. A little cheaper than you can buy one off the site. I have 2 total. PM or email if you want one. Thanks, Mark
Last reply by jmark, -
- 13 replies
- 2k views
Well im moving on up..Really....From Sunny California to Colorado Springs,Colorado in a couple months....How many members are close by??? Would like to meet some of you to get some ideas when I get there. I will be trying to get my first Z when we settle on in...Any info on the area would be helpful....You guys have been great here and hope to be in this club for years...Thanks again
Last reply by brushie1320022, -
- 16 replies
- 3.1k views
What tools are absolute must haves when restoring a car? I have a lot but I want to round out my collection for my birthday.. so far I was thinking of getting these Angle grinder Ball pein hammer and a punch What else can I add to the list?
Last reply by 71datsunZ, -
240z gas tanks 1 2
by nahurry- 13 replies
- 2.7k views
does anyone know where to find a new 240z gas tank?
Last reply by ddezso, -
- 12 replies
- 2.2k views
As I prepare for for this year's NFIBMT (No Frills Iron Bottom Motoring Tour), I'm shopping for a camera and roll bar mount. serching the web has located some "Bullet cams" that connect to a camcorder, but I was more inclined to just mount the camera itself to the roll cage. Anybody has expirence to share?
Last reply by Chino 240Z, -
- 1 reply
- 1.5k views
HEY !!!!!!!!!!!!!!!!!!!!!!!! WHERE"S FUNNYBONE GONE ?????????????????????? Rick. :devious: :devious: OOPS, .... found it. It wasn't there a minute ago. Rick.
Last reply by theianmonster,
-
Recently Browsing 0 members
- No registered users viewing this page.
