Open Discussions
Open discussions about the early S30 series issues and topics.
8,795 topics in this forum
-
- 3 followers
- 11 replies
- 1.1k views
I have made a Drive Tribe for the classic z people, I am not very good with posting stuff but I think it would be cool if we could get something going here! Here is the link to the one I have made, or if any of you have made one or have suggestions, let's hear about it! https://drivetribe.com/t/TawmB2ueRnS4kTVqEJkMwQ/Y1kTCh_cSgeSsJVMfBjFmg
Last reply by Rij Martin, -
-
- 4 followers
- 12 replies
- 7.2k views
can someone help me find jdm/euro rear spoiler? i want nos and i know it's very hard to find or a copy with excellent finish look? this spoiler come with fat right side to install the emblems on it.
Last reply by bpilati, -
- 3 followers
- 9 replies
- 3.9k views
Hey Guys, I am sorry if this has been answered before but I came seem to find what I am looking for. If I want to buy a 240z steering wheel with horn pad and put that into my 1978 280z will that work? I see a lot of issues with horn pads but that seems to be when trying to use a 280z horn pad with a 240z wheel. Thanks
Last reply by gotham22, -
- 5 replies
- 1.2k views
I was replacing the remaining old FI hose (short pieces around the regulator) and while I was doing that I wanted to check the spray pattern on the FI's what a pita to get it all off, but the worst part was a snapped the bolt on the front of the head that is used to attach the metal hard lines for the FI rail. The one on the side is ok (shares the lift plate). The one that broke only has one function, and frankly I don't think it would be a problem if I did not use it. But... I was wanting to get a welder (wire feed type) and I have seen it used to weld on a nut to the broken bit. There is some of the bolt still sticking out but no way is it coming out…
Last reply by Dave WM, -
- 1 follower
- 0 replies
- 577 views
Hey Guys, I am sorry if this has been answered before but I came seem to find what I am looking for. If I want to buy a 240z steering wheel with horn pad and put that into my 1978 280z will that work? I see a lot of issues with horn pads but that seems to be when trying to use a 280z horn pad with a 240z wheel. Thanks
Last reply by gotham22, -
- 1 follower
- 2 replies
- 791 views
How does one set the shift points on a 1971 Z?
Last reply by madkaw, -
My 78' 280z project 1 2 3
by franz- 3 followers
- 26 replies
- 3.5k views
Hey guys, this'll be my build thread since this is my first Datsun and I really want to document this. This beautiful car is my Dad and I's project, with my Dad having owned multiple z32's and Z33's in the past. I have worked on Hondas and Honda scooters so this'll be my first Datsun as well. Now on to the car, this car was owned by the previous owner for over 9 years with a little over 70k miles. It is a factory white Z with the 3 speed auto. It has all new fenders, Tokico suspension, bushings, rear quarter panels, engine mounts, paint and has had the frame rails repaired. Only things to be addressed is that the car currently does not run, and that the entire…
Last reply by franz, -
- 1 follower
- 4 replies
- 1.1k views
Not affiliated with the seller. Just thought this would be a prime candidate if anyone was looking. http://orangecounty.craigslist.org/cto/5892210719.html Thanks,
Last reply by heyitsrama, -
- 1 follower
- 5 replies
- 1k views
I have a 1977 280z with a 5sp with 75k miles. The car sat up for approx 10 years, I purchased it approx 6 months ago and got her up and running. The clutch was slipping and had what I thought was a slight throw out bearing rattle. I had a shop replace the clutch, throw bear bearing and I also had them put a new resurfaced stock flywheel. Within a week or so I have got a rattle that goes away when the clutch is engaged. I can also hear it as I am in lower gears moving but seems to go away as I get into 3 and 4th. The Trans shifts very smoothly. It was suggested that I replace the Trans Lube to a Redline oil. I wasn't able to get it locally so I used a Mobile 1…
Last reply by Dave WM, -
- 2 replies
- 2.3k views
Good afternoon gents - I currently have a "Do It In A Datsun" license plate frame that came with my yellow 1971 240Z (see attached). I'm looking for another rone of these for my silver 240Z. Anyone have one that they are willing to sell ? Any leads? Much appreciated
Last reply by Hank240, -
- 2 followers
- 14 replies
- 1.6k views
So, I'm browsing through Classic Z Cars this morning and bender had found a 73' on ebay. I'm looking at it thinking "nice car!" but not for me. I go to close the tab and I notice the title of the page. Talk about an Omen……..
Last reply by gwri8, -
- 5 followers
- 10 replies
- 9.4k views
I just recently purchased a 240z that needs a bunch of parts. In my search, I haven't found any sites like a Moss parts catalog except for the Black dragon website. The site says it is closing this part of their business down. It looks like exactly the kind of site that would be good for our cars. Does anyone know of any other sites with a nice catalog where parts seems reasonable??
Last reply by goldmember,
-
Recently Browsing 0 members
- No registered users viewing this page.
Yarb
