Open Discussions
Open discussions about the early S30 series issues and topics.
8,797 topics in this forum
-
- 4 replies
- 1.6k views
Can anyone post detailed pictures of mounted Datsun headlight covers ? Especially the mounting fastener area ? I will be installing early 3 screw covers , and I would like to see the installed setup. Also do's and don'ts , maybe better ways to do this - also I will be fabbing the hardware as these did not come with the screws / plates . Thanks !
Last reply by 240ZGL, -
-
- 1 reply
- 876 views
A knee surgery put my schedule back a few months, but the time has come to drop the motor back into the Healey. I picked up the recently rebuilt motor off of a guy parting out his car, cleaned it up and built an aircleaner for my dual webers. I can't wait to get the car back on the road.
Last reply by cozye, -
- 0 replies
- 1k views
The Tidewater Z Car Club is having their annual Z Odyssey Show on Saturday May 14th at Pomoco Nissan;1134 Mercury Blvd; Hampton, Virginia. This is always an outstanding show with a lot of early cars as well as an array of later cars throughout the models. Registration is 9:00 a.m. to 12:00 noon. Contact Todd Wagner at 757-851-8098 or email zfixers@cox.net for info..... $25.00 in advance or $30.00 at the gate.....rain or shine.
Last reply by Diseazd, -
- 3 replies
- 1.4k views
Thought youd might like this. http://www.youtube.com/watch?v=W1pLfowWerc
Last reply by black gold man, -
- 1 reply
- 955 views
Hope you and your families have a happy and safe Easter. Bob:)
Last reply by olzed, -
- 13 replies
- 1.7k views
So yesterday I decide it's time to change out all my coolant hoses and heater hoses etc. I got the "while I'm at its" so I buy a new thermostat. The one I was going to replace turns out to be a Nissan O.E. brass type 180 degree. My local dealer wants $28.00 for a new one, so I bought a replacement at O'reilly also 180 degree. I install the new one and my car immediately reads hotter on the temp gauge by probably 20 degrees from at least two needle widths left of center line to 1-2 needle widths right of center line. I think, well, maybe I've got an air bubble. I leave the car on my driveway which is a pretty good incline and then jack up the front just to make sure…
Last reply by Willoughby Z, -
- 17 replies
- 2.4k views
All-- I was recently fortunate enough to purchase a NOS ashtray assembly for my Series 2 (73) 240Z. In the past we've had discussions about the surface finish of the sliding lid and how difficult it is to restore that when it has been damaged. Does anyone have a suggestion as to how to treat the surface so as to prevent it from oxidizing/tarnishing/staining/marring?? :bulb: I don't intend to use it for it's purpose, but do intend to install it in the car. Any ideas or thoughts are welcome!!! Jim D. "Zup"
Last reply by cygnusx1, -
- 0 replies
- 1.1k views
Does anyone know if the firewall insulation that MSA sells will fit the 280z? Msa titles it as fitting only the 240z. Would there be major modification to it to fit the 280z??
Last reply by az240z, -
- 0 replies
- 1.2k views
I need the hard water (coolant) line that runs along the front of the valve cover. It is the line that supplies coolant to the block under the air regulator on top of the intake manifold. Mine has a pin hole and I can't locate where exactly. It is corroded and I'm not sure it is worth fixing. So I'm hoping to find someone with a parts car or such that can sell me one that is in great shape. Please let me know. Thanks. Bob
Last reply by rcb280z, -
- 1 reply
- 3.6k views
I'd never seen one of these, figured I'd share.... The description is erroneous, but this might be a good way to get your kids into a Z car... http://nashville.craigslist.org/rvs/2339722096.html
Last reply by FastWoman, -
- 12 replies
- 1.6k views
I've been having a hard time with replacing fasteners and a few hose clamps. I didn't originate from the area I live in now and don't know the salvage yards well enough to find another Z any help? PA, DE, Maryland, southen NY, and NJ locations will work. I've called all the salvage yards several times, I'm about to make a trip west to get the parts if I can't find them hear.
Last reply by Decoy12, -
- 3 replies
- 1.2k views
I have a sweet 75 Z I'm thinking of selling. I know I cant get what I have in it, and I have a bias opinion. So I want someone to tell me what I realy have. Is there such a thing as a early Z appraisers?
Last reply by ezzzzzzz,
-
Recently Browsing 0 members
- No registered users viewing this page.
jfa.series1
