Open Discussions
Open discussions about the early S30 series issues and topics.
8,797 topics in this forum
-
- 3 replies
- 1.1k views
Hi. I've seen references to P/N's and microfiches on the site. Where does one get the microfiche for 1971 240Z and/or P/N list? Thx, Simon.
Last reply by Zs-ondabrain, -
-
- 0 replies
- 948 views
Hey everybody, haven't been on the forum in awhile, wish it was on better terms, but i am selling my project Z . Just posted it in the classifieds. Any questions shoot me an email at cky7290@yahoo.com Happy Z'ing guys!
Last reply by zman525, -
- 1 reply
- 3.5k views
all sold
Last reply by Mikes Z car, -
- 1 reply
- 841 views
I've got a 75 280 with 133K on the original motor (getting a little weak) and a 77 L28 with 80K on it, but hasn't been run in probably 10 years. Question is do I swap the old motor for the newer and then rebuild the older or other way around? I don't plan on doing any major engine mods, probably just get valve job on the 77 (B4 swapping) and some minor ignition changes. Clutch definitely has be redone, but there is a decent clutch on the 77 motor. Give me some suggestions. Thanx.
Last reply by d240zx2, -
- 3 replies
- 1.5k views
http://atlanta.craigslist.org/eat/cto/1689888514.html "Always garaged, extemely low mileage, Must see - no rust, leather in PERFECT condition, power windows, cold A/C, black/gold, automatic, louvers on back and side mirrors. 38,383 Actual Miles, All original"
Last reply by moonpup, -
- 5 replies
- 4.4k views
Hi everyone. I have found a trick to clean and remove the rust and paint from parts that I thought I would share with you. If you set up a plastic tank of water mixed with washing soda (can be found next to the laundry detergent as the store) you can use DC electricity to clean off crud and remove paint and rust. You connect the negative lead to the part you want to clean and use a sacrificial piece of steel for the positive. As the water is converted to gas through electrolysis bubbles form on the surface of the metal and it gets under the dirt grease paint and rust and eats away at it. A lot of dirt and crud forms on the positive plate and the part connected to the nega…
Last reply by philbar73, -
- 2 replies
- 1.4k views
I have a couple of problems with my fuel lines that I need help with. First, there are two metal fuel lines in the engine compartment coming from the tank. One is connected to the pump and the other is NOT connected and has, of all things, a golf tee shoved into it. When the tee is removed gas comes out of the line. I am assuming that this is the fuel return line. The car has tripple mikuni's and the fuel line dead ends at the third carb. I am wondering if I need the other fuel line or can I eliminate it? If I can eliminate it, where should I cap it off? Second, when I filled up the gas tank, gas started leaking everywhere... It was apparently near the top of the tank a…
Last reply by 73 240Z Man, -
- 4 replies
- 1.5k views
Hi? i searched but i cant find a thread that talks about lowering method. i want to lower my 76 280z all the way down or close to the tire. i mean bring the fender close to wheel. i dont like the gap. how should i do thi? what do i need to do or what set up should i use to get this result. any suggestion on springs name and shocks. i am going to put 17" rims/wheel on this car. what is the wheel dimension or width that will fit this car without any problem like rubbing. what is the best exhaust/muffler to put on this car that will give it a better deep and smooth sound. i want to put in racing seat. what dimension of racing seat will fit perfectly width and height…
Last reply by rzkas, -
- 26 replies
- 3.8k views
This is just a curiosity. When did each fiscal year roll into the next model year? Would an 11/71 car be considered a '72?
Last reply by Kathy & Rick, -
- 0 replies
- 1.1k views
AutoWeek has an online magazine of Z car history containing their compiled articles from previous issues. Free just for filling out a form or 99 cents if you want to keep your identity a secret. Use this link: http://www.autoweek.com/section/ztastic Dennis
Last reply by psdenno, -
- 6 replies
- 1.5k views
Stumbled upon this. Description is poor, but the pics look promising IMO. I'd look into buying it personally if I had the money or space, but I don't. Thought I'd pass it along. http://fresno.craigslist.org/cto/1681707018.html
Last reply by lonetreesteve, -
- 2 replies
- 1.1k views
My blower fan for the heater and air-conditioner has stopped working. Is there a fuse for it some where? If not how hard is it to replace it and is the part available?
Last reply by ZCurves,
-
Recently Browsing 0 members
- No registered users viewing this page.
Yarb
