Open Discussions
Open discussions about the early S30 series issues and topics.
8,795 topics in this forum
-
- 6 replies
- 1.4k views
Is there an OEM replacement for the red Z that goes into the original hubcaps? Or whats the best way of finding these. I got a nice restorable set of covers, but need two center "Z" Thanks, Randy
Last reply by mally002, -
-
- 2 replies
- 1.2k views
Today when I was checking the Z I found mice under the cowl. I forgot to block the drain tubes I installed so they climbed up and set up house. So while in there why not remove the wiper linkage and clean it up.Now I know why they didn't work so well.Job went well except the only part I can't find is a nylon washer to replace the felt ones under the pivots.Would those battery synthetic washers work for that?
Last reply by mriz, -
- 1 reply
- 1.4k views
I purchased a R180 LSD that came without the stub axles. From what I can gather, the ones I need have the same spline count as the 81 - 84 maximas. Anyone have a set or know of a junkyard that does? My LSD swap is pretty dead in the water until I find a set. Thanks in advance! Bryan Dat240zg 240Z #248 240Z #1693
Last reply by jmortensen, -
- 12 replies
- 2.2k views
Today I picked up the 1970 Series 1 Z car which I purchased on Ebay yesterday. I found a number of parts in the luggage area including this, what looks to be a skid plate. Is this just a rogue part or does it belong on a Series 1?
Last reply by kinfish, -
- 0 replies
- 1.1k views
I took my parking light lens off my 78 Z to clean and check for rust. When the lens came off, the inside assy was half packed with dirt and half the reflective lens on the inside was half eaten up with rust. Went to Ebay bought a replacement set only to find out they were in the same condition. I came up with an idea a week later. Used a dremel tool with a burr bit and shaved off the 2 heads of the plastic rivets holding the reflective lens in place. I removed the lens and wrapped light cardboard around the back sid side and traced a templet. Then took an aluminum soda can cut it down the side with shop scissors, then cut out the top and bottom. The inside surface is coat…
Last reply by Obewon, -
- 2 replies
- 1.2k views
from the release bearing. So, after I made my inquiry in the drivetrain forum, I went ahead and installed the slightly larger T/O collar (new) onto my transmission. Turns out it was slightly too large too. Recap: My A-series transmission had a T/O collar that was to correct for the year. It measured 1-5/16 in. from the top to the back of the release bearing (I did not know this until last night). The 260z 4-speed I am swapping in had a T/O collar that measured 1-1/8 in. (correct for that year). I bought the 280z collar (you can only buy two now - the small one and the large one) which measures 1.5 in. I went against my better judgement (and because I was excited to …
Last reply by ktm, -
- 8 replies
- 2.7k views
This is a very rare sale of the collectible 280Z Zzzap. I happened across it today and thought people might be interested in seeing an original car (except for the wheels!) Anyone else have one out there? It will be interesting to see what this car goes for! The link is: http://cgi.ebay.com/ebaymotors/1977-Datsun-ZZZap-Z-280Z-Special-Edition-Collectible_W0QQitemZ280060405549QQihZ018QQcategoryZ6187QQcmdZViewItem#Photo
Last reply by sblake01, -
- 10 replies
- 2.9k views
Flippin through ebay this am and saw this gem going for sale, a little pricey but really looks clean! http://cgi.ebay.com/ebaymotors/Datsun-Z-Series-1971-Datsun-240z-JDM-Fairlady-style-COLLECTORS-Mint_W0QQcmdZViewItemQQcategoryZ6187QQihZ013QQitemZ230065574217QQrdZ1
Last reply by 76Datsun280z, -
- 9 replies
- 2.2k views
Hey guys, hate to say it, but its true........ http://classifieds.hybridz.org/showproduct.php?product=3483&cat=7 I tried to post it in our classifieds, but I couldnt get it to work.....
Last reply by zeewhiz, -
- 6 replies
- 2.6k views
head swinging mr.k.. http://www.courtesyparts.com/Merchant2/merchant.mvc?Screen=PROD&Store_Code=CP&Product_Code=MRK-BOB1 Funnyyyy T-shirt http://www.zcruiser.spreadshirt.com radio controled 432 http://www.hlj.com/product/TYOA210N I have one of these radican 432 and it even has lights
Last reply by 260z, -
- 16 replies
- 2.6k views
For your consideration-Original Triple Webber Carbs! This is a 71 Datsun 240z HLS30 MFG, Date 5/71 One of 50 in this special run series. Now I don't know a lot about this car as it was inherited to me. But I will tell all that I know about it, you can email me what questions you might have about it. There is a triple carb. on this which are webber. The body does have rust but is straight. All original everything, it currently does not run and would have to be trailored. The engine is a big inline 6 cylinder 3 carb. Yes it has the original triple carb. Wide fender wells, all tires are flat some badly damaged. The battery is gone, all ignition wires are also g…
Last reply by hls30.com, -
- 0 replies
- 2.1k views
Here is a calendar of events for the Lane Museum in Nashville that includes the recently aquired Nissan Heritage Vehicles. UPCOMING EVENTS Click here to read about the 3rd annual Lane Motor Museum Microcar Drive held May 6, 2006. November - Nissan Heritage Collection Race Car Exhibit Now through December 31, 2006. Seven Nissan of North America Heritage Collection race cars are on display and include a replica 1985 Nissan 300ZX Turbo -# 33 Paul Newman/Sharp Trans Am; a replica 1990 Nissan 300ZX Turbo - #75 Steve Millen & Johnny O'Connell GTS race car; and a 1970 Datsun 510 - #46 driven by John Morton, which was the 1971-1972 2.5 Liter Trans Am Champion. All Nissan …
Last reply by Zulaytr,
-
Recently Browsing 0 members
- No registered users viewing this page.
