Help Me !!
This is the emergency HELP ME forum for those of you that are having troubles with your Z-Car and need immediate help.
6,104 topics in this forum
-
- 4 followers
- 11 replies
- 3.7k views
I have 1971 240Z (7/71) and the shifter boot (inner and outer) is completely missing. I see some videos that show the boot ring (retainer), but I'm thinking there may not be a ring for the Series 1. Am I correct that I only use clips to secure the outer boot cover? Any help is appreciated.
Last reply by 7tooZ, -
-
- 3 followers
- 6 replies
- 749 views
Hello, so I was cleaning my turn signal switch and happen to break the circuit board as I was trying to pry it open to clean the contacts. is there any way I can repair this? Any type of conductive adhesive I can apply? What type of services could be able to restore this piece? I would gladly buy this piece as well if anyone is selling it! I have attached a few photos here as well. Thanks!
Last reply by dhp123166, -
- 7 followers
- 49 replies
- 5.3k views
1975 280Z, I bought it two months ago and I just starting to sort it out. The car appears to be fairly stock, in other words, not heavily modified. The previous owner does not have a lot info about the car, it seems he bought the car from someone in Mississippi who did the rebuild and body work. The car starts and runs fine, but it has konked out on me twice. After the car is warmed up, and having driven it for 30 plus minutes, if I drive the car hard, it's starts to stumble, and then it will turn off as I shift gears. When I put it back in gear it runs again. I can keep it going that way for 10 minutes or so before I have to pull over and park it. So I …
Last reply by zspert, -
- 2 followers
- 9 replies
- 2.4k views
Help! I have a 72 240z and the fuel filter in the engine bay is 1/4 full.. under the filter line and wont fill. Just installed a new electric fuel pump and filter, new braided fuel line and a new filter before the mechanical pump but the pressure seems low and it's not filling. As the pump turns on you can see bubbles in the filter (in the engine bay). Question is could there be air in the line? Do i need to bleed a fuel line? Car is hesitating when driving, constantly jerking like its starving for fuel. What could be causing this? Anyone experience this before? Note: Gas tank is half full. Electric fuel pump is 4-7PSI. Got the tank c…
Last reply by SteveJ, -
- 2 followers
- 1 reply
- 589 views
I have a 1/71 production date 240Z that has major front end damage so I'm shopping around for a front clip. My question is what differences are there between the different years and when were those differences? Example, I'm looking at a 6/71 build and wondering if there were changes made from 1/71 to 6/71? My 1/71 has all the expected series I items such as the latching fuel door, no vents in the rear quarter/pillar, etc.
Last reply by 240dkw, -
- 5 followers
- 14 replies
- 13.5k views
Hi all, I've reinstalled my wiper motor & linkage after cleaning & rust proofing the area under the cowel on my '72 240Z. But now my wipers are turning backwards! When I turn them on, they begin with a counter-clockwise rotation (when view from the front bumper). They want to wipe the cowel. Has anyone run into this? I figure that I either assembled the linkage in correctly, or switched the polarity somehow... huh. Any other hypotheses, sage advice? Thanks as always!
Last reply by Johnny280, -
- 2 followers
- 4 replies
- 934 views
So we just putting 7 quarts of oil in my block and the stock dip stick just got wet at the tip. Anybody put this oil pan on their block? Any info would greatly be appreciated. Aloha[emoji1686] Sent from my iPhone using Tapatalk
Last reply by Zed Head, -
- 3 followers
- 11 replies
- 1.7k views
Hello! Long time stalker, first time talker. I hope this is thorough, and let me know if there is something missing. 1978 280z Basically, my car is acting lean. Front firing from the afm... I'll tell you how I got here, what i've done, and any seemingly relevant questions I can’t seem to get an answer on. Been chipping away at getting this car running well for a bit, passed smog (CA) last year. Car was running pretty good minus a rich issue. I was modifying the car back to stock (previous owner put larger injectors/a number of things). We are friends, so I was aware of these changes. Savvy Porsche guy leaned me out to pass smog car ran great all…
Last reply by blackpaw, -
- 3 followers
- 7 replies
- 828 views
Rebuilding a smog pump. Wanting to confirm details. The back casting of the pump looks as if it was black. The pulley, mounting bracket, and adjustment arm Datsun engine blue. Can someone confirm this for me. Also this is all of the parts getting ready for paint, and plating next a set of hoses. I will post more as this project progresses. Thanks PS I am still looking for a confirmed source for the Datsun blue engine paint, not something close but the real deal. If you look closely at the photo I have not blasted the adjustment arm yet, it has a good clean coat of the original paint for comparison.
Last reply by 240260280, -
- 2 followers
- 7 replies
- 898 views
I have a 71 240 that I’ve recently replaced all bushings, bearings and installed coilovers. When driving I can hear a thumping every time the wheel revolves except when I’m on the brakes, then the noise goes away. I’ve replaced the shoes and the drum brake hardware. The lug nuts get crazy hot on the right rear wheel where the noise comes from) from after about 10 mins of driving. Much hotter then the left (no noise side) The car stops fine. I don’t think it’s a bearing issue because the noise goes away when I’m breaking. Ther have been times mid drive when the thumping disappears but it always returns. I’ve taken the wheel off and inspected the drum and dust cover.…
Last reply by Zed Head, -
- 1 follower
- 7 replies
- 2.4k views
Its been a while since I have posted on this site. Hope everyone is doing well. I have been trying to fab a choke cable lever bracket with no success. This is the bracket that mounts under the center console. There is a single slot in my console. There are different brackets, series one does not fit my setup. As I understand it a 1972 – 1973 240z or a 260z choke lever bracket will work. I know this from experience as I have already bought a series one before I found out it would not fit. I would like to either: borrow a bracket so that I can copy it, or buy a bracket at a reasonable price. As always thanks in advance for your assistance. Regards, q
Last reply by qz16, -
- 2 followers
- 4 replies
- 792 views
I'm in the process of refurbishing my 240Z taillights and have run into a problem. The Philips screws that hold the taillight to the rear panel all came out easily on one side, but two of the screws on the other side just spin, so I can not take the light out. Has anyone had this issue and solved it without damaging taillight housing?
Last reply by Randalla,
-
Recently Browsing 0 members
- No registered users viewing this page.
Yarb
