Help Me !!
This is the emergency HELP ME forum for those of you that are having troubles with your Z-Car and need immediate help.
6,099 topics in this forum
-
- 4 replies
- 1.2k views
I have a auto 76 that badly needs a new repaleced tranny. I have a original one in there right now. Should I buy a used tranny or just spend the money on rebuilding a new one?
Last reply by sakijo, -
-
- 1 reply
- 864 views
Anyone know if you can remove the hydraulic lines between the pump and the steering head without taking half the car apart. I've got everything loose but can't work the lines out. seems like the a/c compressor at least needs to be out of there. If you got a trick please let me know.
Last reply by RogerZ, -
- 1 reply
- 1.4k views
Has anyone used the below site? http://www.cheapcarsearch.com/?hop=nsund
Last reply by BD240Z, -
- 4 replies
- 1.4k views
I have a 74 260z, I put all the basics on for a tune-up. Had a mechanic adjust the carbs. He suggusted running carb cleaner thru gas tank. Runs alot better. Hard to start when cold, acts like its flooded. Have to hold gas pedal to floor for it too start. Been reading threads on carbs. Checked to see if choke was working. Seems ok, but when car running and putting on choke, it doesn't change the engine at all. Any help? 74-260z RLS30-011578
Last reply by sugarworker, -
- 3 replies
- 1.2k views
How do you do it??? Manual I have says to adjust idle air screw but I can't find anything on the engine that looks like the picture. Saw a post about changing the AFM around but couldn't seem to relocate that.
Last reply by jfairladyz, -
- 7 replies
- 1.2k views
Car rough idles, replaced PCV/Fuel Filter/Air Filter/Plugs. Car is automatic. It also acts like the battery is dead then fires right up! Passed California Smog with fantastic numbers..... Any ideas?
Last reply by KDMatt, -
- 12 replies
- 1.9k views
I am planning on getting some spring next week and was wondering if i should go with MSA or Eibach. I will also be getting tokiko shocks. Anyone have any experience with any or info they want to share would be great. I don't know if this helps but i will also be installing Sport Max 15X8 sometime after i get my springs and shocks. Thanks for the help
Last reply by CoastGuardZ, -
Does anyone know where I could get the receiver cups and thumbscrews to the T-tops for a 82 280zx? Thx -=Lews=-
Last reply by Darrel, -
- 3 replies
- 1.2k views
83 zxt coolant temp unit was working on the digital dash and then just went black. Speedo tach still in operation. Checked on my other one and not because the sensor is gone I unplugged it on the one that works and the frame work still show just no bars for temp. Anyone worked on one of these and might have an idea if this is fixable. Otherwise I have a complete unit from a 79 is that a direct swap or do wires need to be spliced. any hellp appreciated.
Last reply by RogerZ, -
- 10 replies
- 1.7k views
just put 280Z rears on the car and bled the system but the pedal is really soft to about 5/6 of the way down and the rear brakes dont work. The fronts seem to work fine but the rears aren't working at all, but when you open the bleeder nipple and push the pedal brake fluid comes out. just rebuilt the calipers did i perhaps put them together wrong? anyone dealt with this and know what the problem might be? i am supposed to be racing the car tomorrow but cant at the moment. Thanks, Tom.
Last reply by Darrel, -
- 14 replies
- 1.7k views
I need to remove my A/C unit out of my parts car and I am not sure how to begin. It still has compression and freon left in it. I've got my manual, but don't have the necessary equipment to remove the freon. Are there any other options? I want to be legal here.
Last reply by sblake01, -
- 0 replies
- 1.3k views
I am finally picking up a good parts car and was wondering how would I go about sanding some of the paint. The parts car is white (origanlly blue, same as mine), I think it was spray canned. I need the rear hatch and wanted to primer it black and was wondering how hard this was. The white paint is rough, and I don't know what grit to sand with and how to sand it (worked on rc cars, does this count?), but I can learn. Also I got a brand new 77 280Z hood that is primered gray i think. It is gray and smooth on both the inside and out. was wondering if the part need to be sanded and then primered or just primered. Whats also the typical process of primer? For example;…
Last reply by Midnight-280Z,
-
Recently Browsing 0 members
- No registered users viewing this page.
KenFirch
