Help Me !!
This is the emergency HELP ME forum for those of you that are having troubles with your Z-Car and need immediate help.
6,100 topics in this forum
-
- 5 replies
- 1.4k views
Well my stock '71Z is still running funny. The car seems to idle fine, but when I'm on the freeway at normal speed it will repeadedly backfire through the one of the carbs. When I floor it it will run well up to about 4000, then feels like it's running out of gas or the points are whacked. Also I checked the plugs and they are all kind of white, the 4,5,6 being the worst with a slight flakyness to them. I've replaced the wires, plugs, points, cap and rotor. I thought I ajusted the carbs well, but maybe I didn't? Any thoughts or comments to something I may be overlooking? Thank ya'll
Last reply by kenz240z, -
-
won't start
by MDyer- 7 replies
- 1.9k views
77 280. While in the garage for body work in Dec 04, the car had a lot of trouble starting. Starter would just wind and wind, but car would not fire. Replaced fuel pump, since it was leaking. Thought it might be flooding at the time. Car ran for a week or so, then wouldn't start. Starter would try, but again, it seemed that the engine wouldn't fire:ermm: . Pissed off, I've let the car sit since. ...Until this past Sunday. Charged the battery with a different (better?) charger. Removed the distributor wire from the coil, to see if there was a spark to a ground, and there was none. Buttoned everything back up. Left the battery charging. Monday, just for the hec…
Last reply by richard5vgy, -
- 2 replies
- 1.2k views
I have purchased a urathane bushing kit front and rear and steering rack, it has tie-rod ends and ball joints also. While i am doing this i am planing on replacing the struts, wheel bearings and seals. Is there anything else that i should replace. Do new struts come with boots? Is there a bearing at the top of the strut that should be replaced? I havn't done work on a 240z's suspension before so i don't know exactly what there is that will need replacing. This car sat for 13 years before i got it so i am expecting that most what could be replaced needs to be replaced. Thanks.
Last reply by VaGuS510, -
- 8 replies
- 1.4k views
Drove the car three days ago, no problems. Car has a 5-speed I picked up 3 years ago from Eddie Radatz in Atlanta, don't know what it came out of. I go to take the demon out for a spin today after ripping out the A/C and the tranny won't go into 1st, 2nd, 3rd, or 4th. It will go into 5th, and when in the neutral position, it'll pull as if it's in 2nd or 3rd gear. It will go into what I think is reverse, and the engine will drag as if a load is being put on it, but the car won't move. i look under it and there is a small puddle of what may well be transmission fluid, about a half or 3/4's of a cup. Is the transmission dry? How can I be sure it came out of the tranny…
Last reply by gogriz91, -
- 2 replies
- 2k views
I was going to replace my old cracked steering wheel with a Momo from MSA. The only problem is the new wheels are smaller and fatter and block the speedo and tach for some one who is tall like me. Has anyone had dealings with american-stitches.com on recovering their old steering wheel. Their web site looks impressive. I already did the MSA wheelskins and don't like the look. Tkanks
Last reply by Pennyman, -
- 3 replies
- 1.5k views
Just picked a parts car. Previous owner said it was a Rally engine from a 1970 240z. Does anyone know if I could verify it from the numbers on the engine block?
Last reply by NY " Z ", -
- 2 replies
- 1.7k views
Anyone have the name / # of a good reliable Z mechanic in the NY / NJ area. I'm in Staten Island and have a 72 240 in need of a new exhaust system and carb balancing / adjusting. Thanks for the help.
Last reply by rdefabri, -
- 0 replies
- 1.3k views
after rebuilding the suspension on my 77 280z about a year ago, it stalled one day and I coulnt get it restarted. I havent had time to really mess with it till the other day. I replaced a fusible link wire I thought might be the problem and it started and I drove it, albeit rough it ran okay. the next morning I went out to get it in tune and couldnt start it. found that the cold start valve was leaking from where the electrical connector, connects with the rest of the part. I removed it and covered the hole where it goes. but then found that the cylinders and plugs were being overwhelmed with flooding. I am at a loss please help if you can Thanks In advance CJ Callagher
Last reply by Ccallagher, -
I Just bought a 74 260z with 24,925 miles on the car for $1,000.00 (included is a 71 240z in the price.) The car has been sitting for about 11yrs. The car turns over and acts like it want's to start but won't start. What could the problem be. I think the carbs are gunked up. If they are how do I fix the problem? DeeDee
Last reply by boostedz, -
- 1 reply
- 1.6k views
Hi. I am installing a new brake master cylinder on my 72 240. Is there anyway to bleed it prior to installation so that I don't have to re bleed the entire system? Thanks. Bill.
Last reply by Arne, -
- 5 replies
- 1.3k views
Hello My name Marvis, I need some advice on a problem I have. About a year ago I went out and bought a 240z 71. I thought I was getting a pretty go deal:rambo: . I paid $700.00 for the car $300.00 for shipping. I knew there would be that needed to be done, but I didn't think it would be this much:sleepy: . My biggest concern is all the rust. There is not alot of rust on the body. Most of the rust is on the bottom of the car. You can the ground in alot of spots. When I first got it the car, a few friend and I tryed to get the car running. We got the car …
Last reply by lonetreesteve, -
- 2 replies
- 1k views
She's a runnin!
Last reply by jezze,
-
Recently Browsing 0 members
- No registered users viewing this page.
