Help Me !!
This is the emergency HELP ME forum for those of you that are having troubles with your Z-Car and need immediate help.
6,104 topics in this forum
-
- 1 follower
- 105 replies
- 23.3k views
I was wondering if anyone knows of anyone that reproduces the JDM 5 speed wooden shift knobs. I had a JDM one accidentally fall and the plastic lense/gear map shattered :sick: I was hoping that someone made a repro I could buy?
Last reply by GongZ, -
-
- 6 replies
- 1.3k views
My 72 240z is taking me on a shop tour .....3 trys at 3 shops and I still have a rear wheel that is kinda stuck/ slow turning...binding up......not turning fluidy. Pretty sure brake related... Shop1....Start after I replaced driver side rear wheel cylinder....took back readjust... Shop2....Adjust brake seemed better....but after a short time sticking again bad.... could use of ebrake make this happen? (like it doesnt completely release?) Shop3..."yeah man that brake was locked up....we had to use a rubber malit on it and it broke the brake drum" well I got a new drum....they felt they fixed it....on the way home after a mile I heard a brake related rubbing but this time i…
Last reply by 240260280z, -
- 6 replies
- 1.7k views
I'm looking for an ac belt tensioner for a dealer installed unit on a 72 240z. Does anyone have/or know where I can find one? If someone can post a picture of theirs that would help me a lot. Thanks.
Last reply by siteunseen, -
- 5 replies
- 2.9k views
Hi. I am restoring a 77 280Z. I am trying to repair the windshield washer/ headlight switch. When I received the car, the headlight switch was broken and had been glued back together before being put back onto the stem. This can be seen in the attached picture. Will the windshield washer fluid button pop off so that I can slide this piece back on or will I have take it apart from the other side. I guess I am wondering what the easiest solution is before I spend to much time on this? Thank you for your help. Chris
Last reply by Powderkeg, -
- 1 reply
- 1k views
I'm going to pint my 1976 zx with candy pint. What do you think about the best colour.
Last reply by siteunseen, -
- 3 replies
- 1.1k views
On a test drive today after repairing new injector with bad factory crimp, the short hose from thermostat housing line to manifold blew going 80 mph. Instant steam everywhere. I hobbled off the exit and parked ASAP. The temp gauge pegged. The driver side of the engine bay was pretty soaked. After I repaired the hose and got some water in it, it started and got me home but it ran rough all the way. Do you think its running rough because some things are wet or is it possible I did some more serious damage? 77 280Z n2deep
Last reply by n2deep, -
- 6 replies
- 1.3k views
Im in the midst of rebuilding my cylinder head. Im going to be using the "C" cam for my rebuild, I haven't been able to find anything online about this but in the Datsun rebuild book it says for stock cams use the first notch on the cam sprocket for timing. But a moderately aggressive cam you would use the second notch and so fourth. My question is...Would you use the first or second notch for the "C" cam? I know it came on early 260z's as a stock cam. But it is mildly aggressive since it's a Datsun Competition cam. What would be better for the build? I'm just slightly confused:stupid: Alex
Last reply by Perfect240Z, -
- 2 replies
- 6.2k views
Hi Everyone, I purchased a 72 240z project and now I'm trying to put it together. The PO has bolts all over the place and in misc bags. As of now I am installing the steering column and the radiator. I bought some bolts from Black dragon but they do now have the bolts for the steering column to the firewall, or the radiator bolts(shroud and firewall). Does anyone have a list of sizes for all the bolts? Thanks for your help!
Last reply by hatepotholez, -
- 17 replies
- 1.7k views
Hi all, Been lurking on the site for a bit and finally found the baby I really want to buy, but I'm hesitant. I'm ordering an inspection from AIM this week; I'll update the thread with the results when I get it. The owner assures me it's rust free (yeah, yeah heard that before ), no problems at all but cracked sidewalls on the tires, said he's only owned it two years and doesn't know much about the history of owners or repairs (and he has a very thick accent and is hard to understand so I couldn't really understand what he does know), he had the convertible top done himself and says the only bondo on the car is involved in the frame reinforcement somehow (didn't quite un…
Last reply by Genghis, -
- 2 replies
- 1.4k views
It's not too tough to find a sending unit nut I can't seem to find the o ring seal anywhere! Any ideas would be greatly appreciated. I am new to the Z world but love it so far, just need help with those hard to find items! Thanks in advance
Last reply by siteunseen, -
- 5 replies
- 788 views
Alright so when I drove my datsun with bad(really bad) brakes when I put the brake pedal down all sorts of clicking noises came from under the passenger side of the dash, like a relay only really fast. But now that I fixed the brakes that doesn't happen anymore. But when the key is in the "run" position, and while it is running, there is a relay click sound every ten seconds, under the dash on the passenger side, it sounds like its coming from this cluster of relays. I also hear a relay click every time I hit the horn. My question is, do all 260zs make this many relay cluck sounds or is there something wrong? If its normal, then fine but if its not, then WTH?
Last reply by siteunseen, -
- 5 replies
- 1.3k views
So finally got done with the rear brakes, front struts(among other things) carb swapping and other odds and end, and decided I needed to test her out even just once around the block. I've driven it around the block before, but that was a week after first start, with no power(bad carbs), bad struts, and no back brakes. That was horrible and scary, this however was great! Runs a little rough yet, but pulled hard, steering felt really tight, and nice. Rear struts are still bad and there was alot of crashing and sqeaking back there, so that's next. Then came the brakes, they stopped me good, but I expected a little better, and when I hold them on idle drops about 250 rpms,an…
Last reply by Kurbycar32,
-
Recently Browsing 0 members
- No registered users viewing this page.
