Body & Paint
Discussions about bodywork and painting a Zcar.
3,653 topics in this forum
-
- 2 followers
- 4 replies
- 921 views
Just finished charging battery and while fastening the screw of the battery upper frame i noticed it keeps turning and not tightening the frame to the body. Am i missing a washer here?
Last reply by jalexquijano, -
-
- 2 followers
- 5 replies
- 1.3k views
Hello all, just received front frame rails, pans, and rear supports from Zedd Findings for my 73 240 I have done some searching, but I cant seem to find a good pic of the front frame rail on how to remove it cleanly from the radiator support structure. Looks like it may be pretty complicated to remove without distorting some metal up front. Pics? Advice? Also, whats the best sequence of installation for front rails? Front rails first then go rearward with pans then supports? Thanks all. Note, all components have been removed from the chassis, its a bare shell, just added this pic for reference.
Last reply by wheee!, -
- 1 follower
- 5 replies
- 1.6k views
I borrowed this picture from @motorman7 in his Orange thread. (thanks Rich..) I am helping my neighbor with has series 1 240z restoration. The reinforcement flat plate welded on the rear area of the floor pan, there is one on the driver side of his car but not on the pass side. Is there supposed to be both and what is the purpose, is it just reinforcement?
Last reply by S30Driver, -
- 2 followers
- 4 replies
- 703 views
Zed Heads, Anyone recognize these? Pretty sure they're shims. Door latch, maybe? (I hate having left-over parts!) Thnx, jughead
Last reply by dutchzcarguy, -
- 6 followers
- 15 replies
- 3.1k views
I'd like to find a complete description of how the underside of a 240Z (floors, inner fenders, components, etc.) was finished from the factory. I have to believe there must be a post on here somewhere, but I have searched on a number of topic descriptions to no available. Can anyone help? Thank you.
Last reply by jfa.series1, -
- 3 followers
- 10 replies
- 2.8k views
Photo attached for clarification. The reflective coating inside one of my turn signal lenses has rusted to the point that it is not functional. What would be an effective way to restore this?
Last reply by 7tooZ, -
- 1 follower
- 1 reply
- 881 views
http://www.alfaparts.net/dat280.html His Datsun panel selection is still small but he plans on offering more. Not great photos on his site but the detail looks crisper than Tabco products.
Last reply by Jeff G 78, -
- 1 follower
- 7 replies
- 942 views
Hello all, I have a 1973 240z. The front main seal was leaking and made a bit of a mess under hood. I pulled the engine a while back to reseal the engine a long time ago, and am now just getting back to it. I removed the heavier grease buildup back then, but now I want to cleanup the rest of the grease and grime. (See picture.) However, I do not want to damage the paint, the wire harnesses, or any other components. Does anyone have any recommendations for a cleaner that would be safe? (Eg Simple Green Crystal, or Purple Industrial Cleaner, D108) Any preferred techniques for cleaning it? Thanks! Luis
Last reply by 240Z-Fan, -
- 3 followers
- 11 replies
- 2.7k views
5/71 240z. The wiper arm marked "761 TRICO LD100-L" has failed, where the plastic connects to the blade, and must be replaced. The other wiper arm is marked "621 TRICO LA87R". Should I be looking for a "621 TRICO LA87L"? The wiper arms on my 72 240 are marked "408 TRICO 55-R" and "409 TRICO 55-L". Didn't find posts on this topic, after doing a search. Thanks
Last reply by Freez74, -
- 15 followers
- 41 replies
- 13.4k views
I purchased a can of spray paint from a vendor that was supposed to be a exact match for the taillight panel but it seems to be too light, more of a "battleship grey" than the correct "charcoal grey" . Does anyone have a source for the correct color paint? Also I need to touch up the grey panels on an original set of wheel covers. Does anyone have a source for that color?
Last reply by bpilati, -
- 1 follower
- 9 replies
- 3.3k views
Emblems on rear hatch removed by P.O. and holes are non apparent. Looking for the exact emblems position measurements (Datsun, 240z)
Last reply by HappyZ, -
- 2 followers
- 4 replies
- 756 views
Hello, I have recently acquired new doors to put onto my 1978 280z, but the rails for the window area do not fit on my car. The rest of the door fit fine, just not the metal part on the top. Does anyone know if these rails are adjustable in any way or do i maybe have the wrong door? I have a feeling that i have a 2+2 door but i am not 100% sure. I've read that 2+2 doors are longer so it doesn't make any sense to me how I got it on in the first place if it is indeed a 2+2 door. Any help would be appreciated.
Last reply by zKars,
-
Recently Browsing 0 members
- No registered users viewing this page.
