The story begins here, in Gothenburg...

This is my 1971 240z when I picked it up after arriving in Gothenburg from

Chicago. E"verything" looked "well" - and met my expectations from the pics

in the ebay auction. However - the "rust free" turned out to be a big hoax...

Anyway, after getting it up on the trailer and taking it home to Stockholm

it was unloaded at a friends company - called Speedworks where I assume most of the

mechanical mischief will take place once the car's been restored. The engine

was fired up (or rather jump-started since the ignition wires had been yanked

from it's original place) - picure below.

Vidcap-picture of the car at Speedworks.

The engine wasn't running like it was new, but at least it was running. Not

that it mattered much anyway - the car wouldn't have made it through an

inspection by the swedish "DMV" anyway. As I soon learned, the floor pans

were replaced by a hopeless heap of fiberglass, riveted and bolted pieces of

metal. Click the links below for images of the so called floor...

http://gallery.voodoo-people.com/albums/240z-projekt-Hugo/b12.jpg

http://gallery.voodoo-people.com/albums/240z-projekt-Hugo/b13.jpg

http://gallery.voodoo-people.com/albums/240z-projekt-Hugo/b14.jpg

http://gallery.voodoo-people.com/albums/album185/01_G.jpg

I continued to strip the car of... everything. That was the plan from the start

pretty much, so a "little rust" wouldn't discourage me. When I removed the

dashcap - I was surprised - I have never seen a more messed up dash than this!

Anyway - I got in contact with a company called SCE - Swedish Composite

Engineering - and they will be helping out with molding/making a lot on this

car from carbon fibre. So far the planned parts incluce: The hood, cowl plate,

service hatches, front fenders, doors, rear hatch, center console, dash and

the tail light plates. Since I don't want to completely "out source" the job I'll

be present during the production of the parts, hopefully learning something

Since the car was all together nasty, I figured having it sand blasted would

be the most reasonable thing to do. Said and done - Doors were sent packing.

http://gallery.voodoo-people.com/albums/dag20/00_G.sized.jpg

http://gallery.voodoo-people.com/albums/dag20/01_G.sized.jpg

http://gallery.voodoo-people.com/albums/dag20/02_G.sized.jpg

http://gallery.voodoo-people.com/albums/dag20/03_G.sized.jpg

http://gallery.voodoo-people.com/albums/dag23/05_G.sized.jpg

I think they came back alright... As did the other small parts I sent every

now and then - including the cowl plate, tail light plates, fenders, etc.

http://gallery.voodoo-people.com/albums/dag30/01_G.sized.jpg

http://gallery.voodoo-people.com/albums/dag30/02_G.sized.jpg

http://gallery.voodoo-people.com/albums/dag30/03_G.sized.jpg

http://gallery.voodoo-people.com/albums/dag30/04_G.sized.jpg

http://gallery.voodoo-people.com/albums/dag30/05_G.sized.jpg

http://gallery.voodoo-people.com/albums/dag31/01_G.sized.jpg

http://gallery.voodoo-people.com/albums/dag31/02_G.sized.jpg

http://gallery.voodoo-people.com/albums/dag31/03_G.sized.jpg

http://gallery.voodoo-people.com/albums/dag31/04_G.sized.jpg

http://gallery.voodoo-people.com/albums/dag31/05_G.sized.jpg

http://gallery.voodoo-people.com/albums/dag31/06_G.sized.jpg

http://gallery.voodoo-people.com/albums/dag31/07_G.sized.jpg

After a while, there wasn't much more to dismount from the car, looking like this:

A rotisserie stand was made by Speedworks, from the blueprints of a friend:

http://gallery.voodoo-people.com/albums/dag28/00_G.sized.jpg

http://gallery.voodoo-people.com/albums/dag28/02_G.sized.jpg

http://gallery.voodoo-people.com/albums/dag28/06_G.sized.jpg

http://gallery.voodoo-people.com/albums/dag28/11_G.sized.jpg

Since some parts weren't feeling to good, I called in the reinforcements,

ordering parts from a company called Meca. Tabco wouldn't even reply

to my e-mails even though I had placed an order. Very poor service IMO.

Pictures of the actual parts are here:

http://gallery.voodoo-people.com/albums/hugo-diverse/delar01.jpg

http://gallery.voodoo-people.com/albums/hugo-diverse/delar02.jpg

http://gallery.voodoo-people.com/albums/hugo-diverse/delar03.jpg

http://gallery.voodoo-people.com/albums/hugo-diverse/delar04.jpg

http://gallery.voodoo-people.com/albums/hugo-diverse/delar05.jpg

http://gallery.voodoo-people.com/albums/hugo-diverse/delar06.jpg

So - that's about it. As of now the car stands knee deep in sand at Allblästring

(the sand blasting company) waiting for me to pick it up, but I'm not going

to be able to during this week. Bugger

More pics:

http://gallery.voodoo-people.com/albums/dag32/01_G.jpg

http://gallery.voodoo-people.com/albums/dag32/03_G.jpg

http://gallery.voodoo-people.com/albums/dag32/04_G.jpg

http://gallery.voodoo-people.com/albums/dag32/05_G.jpg

http://gallery.voodoo-people.com/albums/dag32/06_G.jpg

http://gallery.voodoo-people.com/albums/dag32/07_G.jpg

http://gallery.voodoo-people.com/albums/dag32/08_G.jpg

http://gallery.voodoo-people.com/albums/dag32/09_G.jpg

http://gallery.voodoo-people.com/albums/dag32/10_G.jpg

http://gallery.voodoo-people.com/albums/dag32/11_G.jpg

http://gallery.voodoo-people.com/albums/dag32/12_G.jpg

Parts from ZEDD FINDINGS, yay!

http://gallery.voodoo-people.com/albums/dag32/13_G.jpg

The front frame rails will be replaced, along with a bunch of sheet metal.

I got 4 square meters of 20 gauge sheet metal standing by to fill in all the

gaps. Will probably buy a bunch of 18 gauge as well... When all the rust

has been cut away and replaced with healthy new metal, the car will be

hauled back to sand blasting to blast the welds, etc. The entire car will

be painted with POR-15 silver (I know what Escalon [spelling?] thinks of

it - but I've been told by the resellers of POR-15 Germany that it'll be fine

as long as the surface is rough (go over it with block sanding). I'm being

sponsored by the swedish reseller of POR-15, so I reckon It'll be alright.

To be continued...

I got lot's of critique to, but who cares.. i don't see them doeing such a project.

How are things going now mull?

How are things going now mull?

Not much has happened since last. I got hold of some GTR wheels that

I'm trying out for size. They're 16" - tires are 225/45. Good fit. More back

space for a wider rim - approx 15-20 mm - and the flares are now being

redesigned by the same metal worker that did the "too wide" version and

the slimmer ones that are shown in this pic:

Very nice mull. I've been following your project like many here and I am impressed. Your car is going to be one-of-a-kind when your done. Look forward to more updates....

P.S. I love the 16" wheels....

Ahh...watched the entire video series again today on a flight home from Chicago. Just awesome.

You've been quiet for a while...any action?

Cheers,

Ya know, Bart and Mull are quite the artists. Dedicated, intense, imaginative and daring. They know what they want and dedicate their resources to that end. Their Zs will be brilliant in both execution, appearance and performance. It would be our pleasure to see them in person some day.

You fellas rock!

Frank

Well thanks Frank! I think we both have a hell of work to do, Mull is way ahead of me, atleast he got some help. I gotta do it all myself.. Well just takes some more time i guess. I'll keep all Datsun fanatics updated here:)!

Long time no update seen on this car Mull? Still working on it?

Yeah, it's still in the making! Should be some updates during june... : )

Patience is a virtue, or so they say

Great effort on the restoration! Nice videos as well.

Been reading your thread on HybridZ as well.

Anyways, looking forward for more updates!

Time to beat this dead horse with the update-stick!

Trial fitting of a Nissan 200sx S14 front suspension...

...and if you have to ask. No. This. Isn't. Final. Installation.

I think time is your great issue to? I'm still depending on the weekends, to work on her...

But as i can see you will be doing fine to... It's endless work to be done, but once you are finished it will be a cool car!