R-T diff mount Group Buy

[Zs-ondabrain]

As always, Thanks for the Rave Reviews. If you guys keep doing that, The fall from my pedastool will be a long one. Thanks guys.

On to business.....

If all the people that said they mailed an order last week truly did so, My mail carrier is gonna have quite the bundle for me tomorrow. I'll update with each peice of mail with an "Order and Payment Received" next to your name.

I'll also keep updating names and status on post # 114 on page 12.

bajcsi, SSuspect and =Enigma=, you're on. Thanks again guys,

Dave

Edited November 23, 2009 by Zs-ondabrain

[SSuspect]

As always, Thanks for the Rave Reviews. If you guys keep doing that, The fall from my pedastool will be a long one. Thanks guys.

Dave

FYI Dave - Got everything buttoned up in the column tonight (still need to clean up wire under dash). You can see your combo-switch handy work here. Thanks for your help! (sorry for side-tracking the thread)... :stupid:

Tim

Edited November 16, 2009 by SSuspect

[Zs-ondabrain]

Looks good but make sure you tuck those wires before you're done. Or is that an Obvious thing? If you want, repost this in the Review section or on the Combo turn signal service thread. http://www.classiczcars.com/forums/showthread.php?t=24304

Keep us updated.

Dave

Edited November 16, 2009 by Zs-ondabrain

[pbarcher]

I'll take one for my stock 73

Peter Barcher

[Zs-ondabrain]

Just an FYI, I ordered 50 to be made. So if you don't see 50 names on post #65, then they are still available. Peter, you're on the list.

Thanks guys.

Dave

[Zs-ondabrain]

Just got back from the shop and measured up the new Mount. Brought it home and did a quick instal and everything is great.

The pictures below if of the prototype but the production unit will have the oblong holes like the original. Also, back plate will be inset 1/4" like the original. It cleared the brake likes easily but as stated before, the fuel line bracket might need to be moved a few inches forward. But this will also allow you to retain the clamp and not have to remove it, just slide it forward.

All new names were added and a few were updated.

Here ya go.

Dave

[RT Hunter]

Will that bend try to straighten out gradually if the diff keeps thrusting up?

[SSuspect]

Looks good but make sure you tuck those wires before you're done. Or is that an Obvious thing? If you want, repost this in the Review section or on the Combo turn signal service thread. http://www.classiczcars.com/forums/showthread.php?t=24304

Keep us updated.

Dave

I will re-post in the review section. Will post pics of the HLH install too.

I have plenty of "wire management" to finish up under the dash...

Back to this thread... payment sent for the R/T mount!

Thanks again!

Tim

[Zs-ondabrain]

Will that bend try to straighten out gradually if the diff keeps thrusting up?

Absolutely Not. This is 3/16" steel. I can't imagine any 400HP or less motor bending this at all. The back plate is also welded on the sides and top. And if by some weird chance it did bend, I'd like to know what the hell is under the hood. I think you'd snap an axle, U-joint or something else before that would happen.

Good question though,

Dave

[Zs-ondabrain]

Just checked the mail. Got 5 more orders in and updated the names and status on Post #65. Thanks again guys. The New pictures of the Prototype are on Post #78

Dave

[Zs-ondabrain]

Hey Phred, Sorry bout that, you're on the list now. Had a brain-fart

Dave

[70 Cam Guy]

You can count me in, this looks great.

Your fab guy looks like he does great work. Deburred edges, clean bends, clean TIG welds. This coming from someone that was a QE at my last job, inspector before at the same company, and worked for a machine shop during school.

Being a QC inspector can ruin the fun sometimes because after a while, you just notice everything. My friend showed me a ring her bf gave her and I asked her about a flaw that I figured she'd noticed. She hadn't even seen it... I felt like such a jack a** :stupid: