Jump to content
Email-only Log-Ins Coming in December ×

IGNORED

RPM at highway speeds in 4th gear?


BTF/PTM

Recommended Posts

^ thanks! On the same note, is filling the diff as simple as pulling the upper plug and using a manual pump to fill it until the fluid starts to dribble out the hole like with most Japanese gearboxes?
Yes, it's that simple
Well, yes and no. Pumping it in is that simple. But nowhere in the Nissan manuals does it state that you pump it in until it starts to dribble out. The factory always states that "the proper (measured) amount of lube should be added".

It has been my experience with the early-style (Type A) transmission in the '70-71 240Z that if you fill until it dribbles out, you will have overfilled it by 1/4 to 1/2 quart or liter. If you do this, you risk having the excess leak past the front input seal. I wonder if this might be true for the differential as well. I would strongly recommend not overfilling it, but to pump in the specified amount only.

Edited by Arne
Link to comment
Share on other sites

I had a R-200 with 3.90s and in forth I was tacking 3K+ on the Freeway. The car performed super with all kinds of low end. I changed back to 3.54s and now the gearing is right on . At least for me. I am right at 2100 at indicated 60 mph. I now dropped in a 5 speed and it is even much better. Driveabilithy is much better and I am getting 30 MPG to boot. And this is with a moderate cam and a 280 engine .

Link to comment
Share on other sites

^ thanks! On the same note, is filling the diff as simple as pulling the upper plug and using a manual pump to fill it until the fluid starts to dribble out the hole like with most Japanese gearboxes?

A little cleaner method of putting oil in: Remove spare tire well plug above diff, snake a 2 ft section of garden hose through the hole and down into the diff fill hole. Proper amount can be put in without any drips on the floor. This method can be used on the tranny also but the shift boot must be removed.

Bonzi Lon

Link to comment
Share on other sites

205/60R14, probably an inch or two shorter than stock tires.

The stock tire (175/78-14) has an overall height of 24.75", or 6.48 ft/rev, or 815 rev/mile. Your tires have an overall height of 23.69", or 6.20 ft/rev, or 852 rev/mile. So your speedometer will indicate a higher speed by 4.5% (i.e 62.7mph indicated will be 60 mph).

I seem to think that my '71 showed 3100 rpm @ 60mph. My '72 shows 2600 rpm @ 60.

Link to comment
Share on other sites

I love this idea. The center console is out of my car anyway, so getting to the transmission plug won't be difficult.

A little cleaner method of putting oil in: Remove spare tire well plug above diff, snake a 2 ft section of garden hose through the hole and down into the diff fill hole. Proper amount can be put in without any drips on the floor. This method can be used on the tranny also but the shift boot must be removed.

Bonzi Lon

Link to comment
Share on other sites

I checked my speed-o last night. At 60 mph (indicated) I'm showing 2740 rpm. That tells me I have a 3.36 gear ratio in my differential (which makes sense because that's what came on the '72's). I'm not running an OEM tire size. So here's how I calculate actual rpm at 60 mph:

oem - 175/78-14: 815 rev/mile (5280/(24.75 x 3.14/12)) x 3.36 = 2740 rpm

now - 225/50-15: 846 rev/mile (5280/(23.86 x 3.14/12)) x 3.36 = 2840 rpm

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...

Important Information

By using this site, you agree to our Privacy Policy and Guidelines. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.