Jump to content
Email logins are now active ×

IGNORED

280z springs on a 240z


OniZ

Recommended Posts

While it's just temporary until I can afford a real suspension I'm trying cut springs and different spring options. Currently I'm running the normal 240z springs but I found a good set of 280z springs. Now I was told the 280z has a stiffer spring but it's a softer rate than the 240z, is that true? I was looking for a somewhat stiffer ride. I've looked around and haven't seen anything on this mostly 240z springs on 260's and 280's.

Link to comment
Share on other sites

The 280Z springs are quite a bit stiffer - looks like you could cut a coil or 1 1/2 coils off.

As I recall the 280Z's sit higher because they have a taller isolator at the top of the strut.

<pre>

1977 280Z 240Z

FRONT

Spring Rate: 103 lb/in 83 lb/in

Free Length: 15.98 in 15.2 in

Active Coils: 9.5 8.5

REAR

Spring Rate: 127.7 103 lb/in

Free Length: 15.43 in 15.0 in

Active Coils: 8.5 9.5

</Pre>

FWIW,

Carl B.

Link to comment
Share on other sites

  OniZ said:
While it's just temporary until I can afford a real suspension I'm trying cut springs and different spring options. Currently I'm running the normal 240z springs but I found a good set of 280z springs. Now I was told the 280z has a stiffer spring but it's a softer rate than the 240z, is that true? I was looking for a somewhat stiffer ride. I've looked around and haven't seen anything on this mostly 240z springs on 260's and 280's.

280z springs are stiffer than a 240'z, I used the rear insulators from a 240z on my 280z and cut 1.5 coils at the top of the stock springs. Rides lower and more aggressive now.

Edited by johnnyt
Link to comment
Share on other sites

  Montezuma said:
Its all about the isolater, I used a 280 isolator on my 73 when I changed the spring to even out the car. Factory rates are different but aftermaket are all the same except for the isolater.

No, they are not. A little enlightenment is called for.

Link to comment
Share on other sites

One thing to remember...quasi fictional example:

If a Z weighs 2400lbs and is 50/50 weight distribution then you have 600 lbs of weight on each wheel.

If a performance spring is rated 200lbs/ per inch and just fits in the strut without the need for a compressor then it will drop 3" (600lbs / 200lbs/inch) when loaded by the car.

If you have a stock spring that is 100 lbs/per inch that needs to be compressed 6" to fit in the strut then the car will not drop because the 6" of compression preloads the strut to 600lbs.

To properly pre-calculate drop you need:

Corner weights

Spring constant (lbs/inch)

Length of uncompressed spring

Length of spring in unloaded strut

If I had time I would love to collect this data for stock springs.

As mentioned above. Some of the 280z strut isolators are thicker and can lift the car slightly.

lowering%20tech%20tip.jpg

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Who's Online   1 Member, 0 Anonymous, 149 Guests (See full list)

×
×
  • Create New...

Important Information

By using this site, you agree to our Privacy Policy and Guidelines. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.