Jump to content
We Need Your Help! ×

IGNORED

Installing Aftermarket Stereo Receiver - Wiring Question


UR2H

Recommended Posts

Can someone tell me which wire they used for the constant power?

Before I tap a wire not in the general area in where the stereo sits, I was wondering which wire other Z owners were using.

Edited by UR2H
Link to comment
Share on other sites


Details please. Year mostly. I just installed a Pioneer in my 83 2+2. My factory digital unit had one connector for battery power, ign. power, ground, and antenna signal. AND it had a second connector for speaker output. I just probed the wires in the first with a 12 V test light with the key on and off to determine which were which. Of course the black is the ground, cant remember the colors of the power wires, but I can tell you that the factory stereo had a green wire (12 V output) that goes to the antenna timer. That is the one you would connect to the blue wire of your new head unit for the power antenna. I also mounted the factory mid/long range antenna switch in the factory location to retain the factory function of the antenna.post-29105-14150823461385_thumb.jpg:cool:

post-29105-14150823460529_thumb.jpg

post-29105-14150823460785_thumb.jpg

Link to comment
Share on other sites

Can someone tell me which wire they used for the constant power?

Before I tap a wire not in the general area in where the stereo sits, I was wondering which wire other Z owners were using.

I know of no standards for rating auto audio power outputs but if the unit is capable of an honest 100 watts (2 X 50w or 4 X 25w) I recommend running a fused line straight to the battery. Even if it isn't, it keeps it a little cleaner by the fusebox this way.

To answer your question: Tap a circuit that is live with the ignition off. Headlights, hazard lights, parking lights, dome / interior are usual suspects. I'd avoid the headlight circuit simply because they have a pretty heavy draw themselves and while you wouldn't notice if the dome light circuit fuse blew while blowing along at 80 mph at 2:00 in the morning, you definitely, and not in a good way, notice if the headlight circuit blew.;)

Chris

Link to comment
Share on other sites

UR2H-

As Classic83Owner mentioned, it really helps to start off with mentioning your specific year &model; otherwise the comments you'll get are probably for a 240Z/S30

I wanted to run a new line from the battery for the radio, but there were already a couple added, so I replaced the whole (accessory feed system) with 1 wire to an insulated stud located in a inconspicuous place by the battery, and the accessory lines go from that. Also, the firewall grommet is probably stuffed tight with wires, so forcing yet another heavy line through is not a good idea, unless you plan to cut another hole for a second feed-through grommet. After all the wires are in place, you can wrap or cover the exposed wires to look like it all belonged there.

Don't forget to make a drawing or notes in your vehicle's logbook, so you will later know what wires are which and go to what.

Link to comment
Share on other sites

To end the tangent, the OP has a 77. The constant power is just for the memory, so it will not draw much power.

As for the draw of the head unit, look in the owner's manual for the unit and find its rated draw. Remember that fusing should be rated to protect the wires, not the components. If the draw of the head unit is too much, add a relay to one of the accessory circuits. (See Relays Simplified | Fiddling With Z Cars for information on connecting the relay.) For the switched power, you can then tap off the battery as Tomohawk suggested, run that wire to an inline fuse and through the relay to the head unit.

Be sure the select the appropriate gauge wire. If you don't know how, ask.

Link to comment
Share on other sites

From the radio installations that I've done, they all had a 1A fuse on the memory wire, so it probably needs far less than 1amp. Unless your radio harness connector has a live wire on it, the hazard switch or clock, or cigarette light sounds like an acceptable place to tap for the memory power line.

Link to comment
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Who's Online   0 Members, 0 Anonymous, 381 Guests (See full list)

    • There are no registered users currently online
×
×
  • Create New...

Important Information

By using this site, you agree to our Privacy Policy and Guidelines. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.