nix240z Posted January 1, 2014 Author Share #85 Posted January 1, 2014 Fuel sending/fuel pump wiring harness grommet, located in the right rear hatch area. Link to comment Share on other sites More sharing options...
AZ-240z Posted January 1, 2014 Share #86 Posted January 1, 2014 Steve,Is this the grommet that protects the sending unit wire harness where it passes throught the rear deck floor? If so, I'll add it to my llist.Dan Link to comment Share on other sites More sharing options...
nix240z Posted January 1, 2014 Author Share #87 Posted January 1, 2014 Steve,Is this the grommet that protects the sending unit wire harness where it passes throught the rear deck floor? If so, I'll add it to my llist. Dan yes... Link to comment Share on other sites More sharing options...
nix240z Posted January 2, 2014 Author Share #88 Posted January 2, 2014 Antenna Drain tube grommet, located left rear wheel well area. Link to comment Share on other sites More sharing options...
nix240z Posted January 5, 2014 Author Share #89 Posted January 5, 2014 Speedometer cable grommet on firewall. Will need to be cut and glued back together, I machined so it has some meat in the center for easy gluing, plus hole in firewall will help hold it together. No other way around this, since ends of speedo cable are large and will not come off. I will list on website when ready for purchase. 240zrubberparts.com Link to comment Share on other sites More sharing options...
nix240z Posted January 9, 2014 Author Share #90 Posted January 9, 2014 another NLA part. I had a few request for this part. Any other interest in the dust boot for the handbrake in the transmission tunnel? I machined up the part and ready to mold and cast. leftside is the machined part and rightside is the original. Steve Link to comment Share on other sites More sharing options...
Montezuma Posted January 9, 2014 Share #91 Posted January 9, 2014 This is a part I was going to ask about. You are on it. I have to check out your website.another NLA part.I had a few request for this part. Any other interest in the dust boot for the handbrake in the transmission tunnel? I machined up the part and ready to mold and cast.leftside is the machined part and rightside is the original.[ATTACH=CONFIG]69037[/ATTACH]Steve Link to comment Share on other sites More sharing options...
Montezuma Posted January 9, 2014 Share #92 Posted January 9, 2014 I need a set of seals for factory headlight covers. I can get a set of originals to copy. Link to comment Share on other sites More sharing options...
AZ-240z Posted January 9, 2014 Share #93 Posted January 9, 2014 STeve,Do you have an illustration of where this handbrake dust boot is mounted? I couldn't find a part number or reference on my parts CD. On my last fun drive,I did notice a cool breeze of air coming from the handbrake boot, but couldn't determine the source. This probably going to be added to my shopping list.Dan Link to comment Share on other sites More sharing options...
nix240z Posted January 9, 2014 Author Share #94 Posted January 9, 2014 Sorry I dont think I can help you out on these. I need a set of seals for factory headlight covers. I can get a set of originals to copy. Dan, it is the circled part.. STeve,Do you have an illustration of where this handbrake dust boot is mounted? I couldn't find a part number or reference on my parts CD. On my last fun drive, I did notice a cool breeze of air coming from the handbrake boot, but couldn't determine the source. This probably going to be added to my shopping list. Dan Link to comment Share on other sites More sharing options...
nix240z Posted January 10, 2014 Author Share #95 Posted January 10, 2014 (edited) update on the firewall speedocable grommet. The grommet is done and I am testing the glue to hold it together after cutting. Regular superglue works fine, I have the grommet glued back together and under a stretch test of 150% of the cable size, to see if it comes apart. I have also ordered some loctite 406 which is made for rubber and high heat. Once I complete the tests I will report my findings. Steve Edited January 10, 2014 by nix240z Link to comment Share on other sites More sharing options...
EuroDat Posted January 10, 2014 Share #96 Posted January 10, 2014 update on the firewall speedocable grommet. The grommet is done and I am testing the glue to hold it together after cutting. Regular superglue works fine, I have the grommet glued back together and under a stretch test of 150% of the cable size, to see if it comes apart. I have also ordered some loctite 406 which is made for rubber and high heat. Once I complete the tests I will report my findings.[ATTACH=CONFIG]69066[/ATTACH] Steve Love the R&D. 150% is a tough test. Chas Link to comment Share on other sites More sharing options...
inline6
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now