Chickenman Posted June 4, 2017 Share #49 Posted June 4, 2017 (edited) Not really. The VW/Audi 1.8T injectors are a use a flat disc ditribition plate. This has twin laser etched holes to give a very wide spray pattern The pintle caps are special for these injectors. They have a very wide Bevel or countersink on them to allow for the spray pattern to " Fan out" with out hittiting the sides of the Pintle cap. Changing to a different style of Pintle cap may cause the spary to be disrupted. Here is a picture of the Bosch 1.8T pintle caps. Note the wide countersink on the base ( Brown pintle cap ) compared to a Narrow spray Bosch pintle cap: 1.8T Pintle cap: It's hard to see in this picture. But the Blue Bosch pintle caps are designed for a narrow spray pattern Note the subtle difference. Edited June 4, 2017 by Chickenman Link to comment Share on other sites More sharing options...
Chickenman Posted June 4, 2017 Share #50 Posted June 4, 2017 (edited) As I recall, the ZX Pintle caps are much longer than the 1.8T caps. The ZX pintle caps will disrupt the spray pattern of the 1.8T injectors. Edit: This is an image I found on the Web of 280ZX injectors. The pintle cap is quite long. If the pintle caps you put on the Bosch 1.8T injectors look like these, the spray pattern will be severely disrupted. How bad exactly, I don't know... But the spray pattern is going to hit the walls of the pintle cap and that can't be good. 280ZX Injector picture: Edited June 4, 2017 by Chickenman Link to comment Share on other sites More sharing options...
siteunseen Posted June 4, 2017 Share #51 Posted June 4, 2017 Those look completely different. Sorry I ask. 8^( Link to comment Share on other sites More sharing options...
madkaw Posted July 6, 2017 Author Share #52 Posted July 6, 2017 Well I took Richards advice and put the proper pintle caps on the injectors. I did find out that the injectors I am using have a 18 degree spray pattern . Not sure how that compares to stock. All I know is that this engine runs as good as it ever has- despite finding a valve nick on #1 bore , despite dropping the cam with towers attached from 4 feet in the air. Despite replacing a cam tower that was nicked on its bearing surface from the drop. Despite shaving another 20 thou and not checking clearances despite guessing cam timing and throwing the cam in 6 degrees advanced. and the list goes on thankyou L gods 1 Link to comment Share on other sites More sharing options...
Zed Head Posted July 6, 2017 Share #53 Posted July 6, 2017 Did you power them up and give a few squirts? Just to know if the other caps were a problem. Link to comment Share on other sites More sharing options...
madkaw Posted July 6, 2017 Author Share #54 Posted July 6, 2017 Is was more about avoiding a POSSIBLE problem then fixing one. Improperly fitted caps could lead to dribbling fuel collected in the caps that could lead to a bad idle and other issues. Link to comment Share on other sites More sharing options...
Zed Head Posted July 6, 2017 Share #55 Posted July 6, 2017 That's why some squirts would have been neato. It would have shown. Oh well. I often wish I'd taken pictures of things but when I'm doing them I'm just too focused on getting the job done. Link to comment Share on other sites More sharing options...
madkaw Posted July 28, 2017 Author Share #56 Posted July 28, 2017 Figured I'd update this thread( I have too many), but still very happy with my MS conversion. I actually think my tune has brought me close to the power levels I was running on triples . I am happy to have this kind of performance with just an N42 intake and my little amount of experience with MS. It's a steep learning curve , but there are folks that can help in this site and others to get someone going. Programmable ECU is a viable way of getting serious performance without switching to carbs ( for you guys with EFI Z's ) Can't thank Chickenman enough for his support . I owe him a couple more dinners - at least - but I will take care of him! Link to comment Share on other sites More sharing options...
Zed Head Posted July 28, 2017 Share #57 Posted July 28, 2017 Winner, winner, Chickenman dinner... 1 Link to comment Share on other sites More sharing options...
madkaw Posted July 28, 2017 Author Share #58 Posted July 28, 2017 44 minutes ago, Zed Head said: Winner, winner, Chickenman dinner... Link to comment Share on other sites More sharing options...
Chickenman Posted July 28, 2017 Share #59 Posted July 28, 2017 It's all good Steve, I'm getting too fat already Link to comment Share on other sites More sharing options...
zKars
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now