Oiluj Posted September 1, 2014 Share #1 Posted September 1, 2014 (edited) Last few days I've been driving my 72' 240, and noticed a couple strange events. Observation #1) Normal oil pressure at speed, (2/3 to 3/4 on gage), but while sitting at a stop light, gage registers "zero" oil pressure. I blip the throttle up to maybe 15 RPM, and pressure bounces up to 1/3 or higher and stays there... No additional noise from valve train or anything else to indicate a loss or reduced lubrication. Oil level is fine and oil is clean. I searched the threads, and yes, I have a gold color sender. Thing is, it's never done this before... Observation #2) Everything's good, then temperature bumps-up from center of the gage to almost 3/4! This is in-town, stop-n-go traffic. She doesn't act or sound different, (like she's overheating), but again, it's a new behavior. BTW, this does not happen in conjunction with low pressure reading, they seem to be unrelated events. I checked water level and while a tiny bit low, is fine. Have not checked operation of the thermostat or radiator cap, though I don't se why they would change... Was running with the ignition retarded about 7-10 degrees to see if minor pinging at WOT could be eliminated. No difference, but retarded ignition resulted in intermittent dieseling when shutting engine down. So this weekend, I advanced timing 7 degrees which seems to run better and no dieseling. Sadly, I'm stuck using Kalifornia 91 octane, (if you are lucky), + alcohol fuel, so I guess I'll just not push her when going up steep hills... A friend with an older Porsche has a similar issue with low octane fuel. Any thoughts? Edited September 1, 2014 by Oiluj Link to comment Share on other sites More sharing options...
Oiluj Posted September 1, 2014 Author Share #2 Posted September 1, 2014 The excessive oil pressure thread got me thinking. I'm running a Fram oil filter. Was thinking that perhaps the bypass valve is open and I'm losing pressure there, enough to lower pressure at idle below the oil pressure sensor threshold... Link to comment Share on other sites More sharing options...
madkaw Posted September 1, 2014 Share #3 Posted September 1, 2014 #1 - install 20$ gauge from autozone and observe oil pressure OTHER than an electric signal.#2 - the gauge is there to warn you of possible troubles. Things do change in an instant with 40 year old cars. Check complete coolant system Link to comment Share on other sites More sharing options...
djwarner Posted September 1, 2014 Share #4 Posted September 1, 2014 (edited) The oil pressure sender is constructed so that until you reach 6-8 psi the terminal is open. Once pressure reaches the magic number, resistance drops to 60 ohms. As pressure increases, resistance drops down to about 15-20 ohms at 90 psi. Remember the oil pump is a constant displacement pump and only generates whatever pressure necessary to push out it design volume each revolution. The bearing in our engine relies on a flow of oil to prevent metal to metal contact - flow, not pressure. Coming to an idle stop after a high temperature run has oil very thin and runny. It takes very little pressure to push the oil out. As the pressure drops below the 6-8 psi range, the sender opens and the gauge goes below zero to the peg.This phenomena has existed in our cars since they were new. After 44 years, I guess this is properly classified as normal operation.As for your temperature spike, you don't say whether you are running AC which would aggravate the situation. Another cause may be your thermostatic fan clutch allowing the fan to freewheel. Consult the FSM to understand the theory of operation.Hint for boosting octane to control pinging. Try adding about 5 ounces of acetone to a full tank. This will boost your octane rating 3-4 points. If it solves the problem, you know where to look. Though run-on is normally caused by carbon accumulation which can be caused by an overly retarded spark. Edited September 1, 2014 by djwarner Link to comment Share on other sites More sharing options...
Oiluj Posted September 1, 2014 Author Share #5 Posted September 1, 2014 I plan to hook-up a mechanical gage to the port this week, though I suspect, as posted above, everything's all functioning normally.Am already adding acetone, (mixed with a small amount of Marvel's Mystery Oil), and it does seem to help reduce pinging at WOT or under load going up a steep hill, but not it's gone completely. I have no audible pinging at all in normal driving. I've tried added a several gallons of 110 race fuel to a tank, and no pinging under any conditions, but it's a pain to get and expensive...Regarding cooling, I wasn't running the A/C. The fan clutch shows no evidence of leaks, but bears some investigation. I'll check it out. I checked the timing today and it was a 3 degrees too far advanced, so I set it to factory spec. This doesn't seem far enough out to cause the engine to run hotter.Think I'm going to add a coolant recovery bottle as well. I have a heavy-walled, 1 quart round poly bottle, (Nalgene), I've been planning to make into a coolant reservoir.Thanks for the input! Guess I've got some more detective work to do... Link to comment Share on other sites More sharing options...
djwarner Posted September 1, 2014 Share #6 Posted September 1, 2014 Just how are you measuring your timing? Static timing or with a timing light?And do you still have a stock distributor/ignition? And what rpm? Is the vacuum advance disconnected? If you have a vacuum gage, you might try adjusting timing for maximum idle vacuum. Link to comment Share on other sites More sharing options...
Oiluj Posted September 2, 2014 Author Share #7 Posted September 2, 2014 I have a Pertronix ignition. Timing checked with a timing light, vacuum disconnected at 750 RPM. (My vacuum advance is not connected at this time).I do have a vacuum gage and will try adjusting for max vac at idle. Link to comment Share on other sites More sharing options...
John Coffey Posted September 2, 2014 Share #8 Posted September 2, 2014 Do not add marvel mystery oil, or any oil to your fuel. You're actually reducing the octane of the fuel and adding combustion by products that increase carbon build up. Link to comment Share on other sites More sharing options...
Oiluj Posted September 3, 2014 Author Share #9 Posted September 3, 2014 Thanks! No more MM oil... Link to comment Share on other sites More sharing options...
Oiluj Posted September 18, 2014 Author Share #10 Posted September 18, 2014 OK, I verified that I do have oil over 12 psi oil pressure at idle when hot, even when the dash gage indicates zero, so all is good.However....this weekend, when travelling down hill on a cool, foggy morning, for an extended time, (10 minutes), my temp gage dropped to about 120 degrees. I've previously verified dash gage readings vs. a digital thermometer. Temp came right back up as soon as the engine was loaded. Guess I now need to check operation of my thermostat... Link to comment Share on other sites More sharing options...
conedodger Posted September 18, 2014 Share #11 Posted September 18, 2014 Julio! Quit looking at the gauges and drive! :-) Link to comment Share on other sites More sharing options...
Carl Beck Posted September 18, 2014 Share #12 Posted September 18, 2014 Julio - what radiator are you running? Has it been pulled, flow tested or re-cored lately?By all means, do a pressure test on the radiator and cap first.Carl B. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now